9
X-Line 10K RGB
User manual
DMX Mode
：
DMX Channel mode Selection. You can choose the early version of the 18 channel mode (V10 software version), the
later improved 25 channel mode (V20 software version).
Show Mode: Built-In Program Mode. Includes Auto/Sound/ILD/PRG/Outdoor/TEST, ILDA mode (computer laser software control)
for no built-In P mode
RRG:
TF PRG mode (playlist mode) play PRG file. The LCD shows current playlist name, rotate button to change the playlist, press
the button to change current folder.
ILD:
TF ILD mode, play single ILD file (extension name is .ILD, case insensitive) repeatedly. The LCD shows the current playing ILD file
name, rotate button to change ILD file; press the button to change current folder.
Sound:
Play built-in music/sound programs, rotate button to change sonic rhythm.
Auto:
Play built-in auto programs.
Outdoor:
Play built-in auto programs for outdoor place.
DMX:
Control with DMX512 signals. The LCD shows the current mode and DMX address.
SD File:
SD/TF Card file/folder Selection. Exit menu to select the required ILD files in the main interface. Exit the main interface
from the menu interface need to press the knob twice. Don't push or pull the card when power on
Speed:
Scanner speed setting. 8 KPPS~40 KPPS. Suggested to set at 20~30 KPPS, visual scanner speed level to set, if the speed is
too low, the pattern flashes distortion deformation. At higher speed, if the large angle pattern and complex pattern, the motor load
is easy to damage the scanning head. Especially with computer laser software control (ILDA mode), we should pay attention to the
computer software set scanning speed, can’t exceed the scanner can withstand the limit
Slave Mode:
Master/Slave mode setting
。
If master-slave synchronization is required, only one is set Master, and the remaining
machines are set in slave mode to achieve master-slave synchronization effect. In DMX mode, all settings Slave, otherwise Master
the machine will interfere with the DMX signal.
RJ45-ILDA:
RJ45-ILDA signal on/off settings. DB25-ILDA signal can be automatically recognized, RJ45-ILDA due to the limited
number of pin signals can not be automatically recognized, need to be manually set. ON
：
ILDA mode, RJ45-ILDA and DB25-ILDA
interfaces are valid; if there is no ILDA signal, close the light. OFF
：
off RJ45-ILDA, go to built-in mode
Load Flash
：
Program downloads on/off settings. The system only downloads one folder program, the program that needs to be
downloaded is stored in the folder under the card root directory, and only one folder is made.
DMX State:
DMX status settings. Show: No DMX signal is received; the built-in operation mode is run. Black: If the signal is not
received, the light is black.
System priority to read TF card programs. When a TF card is detected, but the card has no ILD file, no matter what the built-in
mode, laser is always closed, so the TF card must have a ILD program file, otherwise, do not insert the card.
To read a Flash memory program, you need to Load Flash the program. After downloading, you can not plug in the card, and then
select PRG/ILD mode. If the card is inserted, it is read card program file
Attention
1. The system just support short file name, file name (include folder name), most 8-bit file name and 3 extension name, file name
and extension name formed by letter, number and under line. File name can’t over 8 and no Chinese words, otherwise the system
can’t identify it.
2. CF card can’t mix other file, most support 20 folders, every folder can save maximum 255 files and 10 PRG files.
3. Program table: user can use notepad to edit program list, the extension name is .PRG. Program table formed by play file name,
play speed, play times. Edit item, for example: one program formed by File1.ild, File2.ild, File3.ild. File1.ild play speed is 30K, replay
20 times; file2.ild play speed is 25K, play 10 times; file3.ild play speed is 30K, play 15 times. Then prg1.prg contents as below:
File1.ild,30,20
File2.ild,25,10
File3.ild,30,15
When create one folder, need create the same PRG file under the folder, and put all the files need to play in the folder into the PRG
file. For example, under aurora folder, create aurora.prg file. After adding ILDA file, need add the file to prg file, so that we can find
the file quickly and play the file as per the speed you set.
