Nice Pro-LT Instructions And Warnings For Installation And Use Download Page 6

SAFETY INSTRUCTIONS 

TO REDUCE THE RISK OF INJURY OR DEATH: 

READ AND FOLLOW ALL INSTRUCTIONS 

Do not allow children to play with door. 

Before installation, be sure that operator i8 suited for type of door and application 

Connect a reversing device to prevent entrapment if door is located near pedestrian traffic. 

Place control device within clear sight of the door but at a minimum distance from the door so 

that user cannot reach moving door parts when operating. 

Outdoor external devices should have security features to prevent unauthorized operation of the 

door. Never cross under a moving door. 

Press the "OPEN" device or activate quick release disconnect device if a person is trapped under 

the door. 

Do not use disconnect mechanism or manually operate door unless power has been electrically 

disconnected. 

Keep doors properly maintained. Test door and service regularly. Have a qualified service person 

make repairs. 

An unmaintained door system could cause injury or death. 

The owner or users must understand the safety and operation of door system. Insure that this 

installation manual be located close to the door system. 

Summary of Contents for Pro-LT





















Reviews: