Nibe F1255PC BE User Manual Download Page 14

Page: 14 / 88

MENU SYSTEM

When the door to the heat pump is opened, the menu system’s four
main menus are shown in the display as well as certain basic information.

INDOOR CLIMATE

HEAT PUMP

INFO

HOT WATER

Indoor temperature - (if room sensors are installed)

Hot water temp.

Temporary lux (if activated)

Outdoor
temperature

Estimated amount of hot water

Information about
operation

INDOOR CLIMATE

Setting and scheduling the indoor climate. See

page 25

Menu 1

HOT WATER

Setting and scheduling hot water production. See

page 44

Menu 2

INFO

Display of temperature and other operating information and access to the alarm
log. See

page 48

Menu 3

HEAT PUMP

Setting time, date, language, display, operating mode etc. See

page 52

Menu 4

NIBE F1255PC

Chapter 2 | The heat pump – the heart of the house

Summary of Contents for F1255PC BE

























































































Search results

Summary of Contents for F1255PC BE

Reviews:

Related manuals for F1255PC BE

Brands by name

Popular brands

Nibe F1255PC BE, User Manual

Search results

Summary of Contents for F1255PC BE

Reviews:

Related manuals for F1255PC BE

Brands by name

Popular brands