Nibe EMINENT E 100 Installation And Maintenance Instructions Manual Download Page 19

17

EMINENT

GB

Maintenance

Dealing with malfunctions

Check the installation's fuses as well as the thermostat 

and mixer valve settings.
Wait a few hours without tapping any hot water and 

then check whether the temperature level has risen. If 

there is still no hot water, contact the installation engi-

neer.

Resetting the temperature limiter

If the temperature limiter (5) tripped, the water heater 

must cool for at least one hour before it can be reset. 
1.  Remove the plastic cover (2).
2.  Press the button on the temperature limiter lightly, 

max 15 N (approx. 1.5 kg).

Max. 15N

LE

K

5

6

2

LEK

LEK

LEK

LEK

LEK

Max 15 N (approx. 1.5 kg)

Electrical installation and service must be 

carried out under the supervision of a qual-

ified electrician.

If the power cable is damaged, in order to 

prevent a hazard it must be replaced by the 

manufacturer, its authorised service agent 

or other qualified person.

NOTE!

Reconnecting sensors

If the immersion heater has been replaced, the sensors 

for the thermostat and temperature limiter must be re-

installed in the order displayed in the image.

LEK

LEK

LEK

LEK

LEK

Service

For service, contact the installer. The serial number (95), 

(14 digits) and installation date should always be stat-

ed. Only electrical equipment supplied by NIBE AB in 

Markaryd may be used.

Summary of Contents for EMINENT E 100

























Reviews: