background image

You also can select the PXIe-1090 chassis fan mode using a DIP switch. Refer to the 

DIP

Switches

 section for more information.

Note

 

The DIP switch must be in the Auto position for software configuration in

MAX to work. If the DIP switch is in the High position, the chassis fan mode will be
High regardless of the software setting.

PXI Express System Configuration with MAX

The PXI Platform Services software included with your chassis automatically identifies your
PXI Express system components to generate a 

pxiesys.ini

 file. You can configure your

entire PXI system and identify PXI-1 chassis through Measurement & Automation Explorer
(MAX), included with your system controller. PXI Platform Services creates the

pxiesys.ini

 and 

pxisys.ini

 file, which define your PXI system parameters.

Note

 

The configuration steps for single or multiple-chassis systems are the same.

MAX provides the following chassis information:

Asset information, such as serial number or part number

Chassis number

Voltages, temperatures, and fan speed

Fan and cooling settings

Slot details

Chassis self-test

Firmware update

18

  | 

ni.com

  | 

PXIe-1090 User Guide

Summary of Contents for 787040-01























Reviews: