NGX Technologies BlueBoard Base User Manual Download Page 15

UM-BlueBoard Base                                                                              

 

 

Page | 15 

 

Information

 

 Revision History 

 

version:

 

v

1.1 

author:

 Vivek Aggarwal & Sandeep

 

 Legal

 

NGX Technologies Pvt. Ltd. provides the enclosed product(s) under the following conditions: 

 

 This  evaluation  board/kit  is  intended  for use  for  ENGINEERING  DEVELOPMENT,  DEMONSTRATION,  EDUCATION  OR  EVALUATION 

PURPOSES  ONLY  and  is  not  considered by  NGX  Technologies  Pvt.  Ltd  to  be  a  finished  end-product fit  for  general  consumer use. 
Persons handling the product(s) must have electronics training and observe good engineering practice standards. As such, the goods 
being provided are not intended to be complete in terms of required design-, marketing-, and/or manufacturingrelated protective 
considerations,  including  product  safety  and  environmental  measures  typically  found  in  end  products  that  incorporate  such 
semiconductor  components  or  circuit  boards.  This  evaluation  board/kit  does  not  fall  within  the  scope  of  the  European  Union 
directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may 
not meet the technical requirements of these directives or other related directives. 

 

 The  user  assumes  all  responsibility  and  liability  for  proper  and  safe  handling  of  the  goods.  Further,  the  user  indemnifies  NGX 

Technologies from all claims arising from the handling or use of the goods. Due to the open construction of the product, it is the 

user’s responsibility to take any and all appropriate precautions with regard to electrostatic discharge. 

 

EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, 

SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. 

 

 NGX Technologies currently deals with a variety of customers for products, and therefore our arrangement with the user is not 

exclusive. NGX Technologies assumes no liability for applications assistance, customer product design, software performance,  or 
infringement of patents or services described herein. 

 

Please read the User’s Guide and, specifically, the Warnings and Restrictions notice in the User’s Guide prior to handling th

e product. 

This notice contains important safety information about temperatures and voltages. 

 

 No license is granted under any patent right or other intellectual property right of NGX Technologies covering or relating to any 

machine, process, or combination in which such NGX Technologies products or services might be or are used.

 

 Disclaimers 

 

 Information in this document is believed to be reliable and accurate. However, NGX Technologies does not give any representations 

or    warranties,  expressed  or  implied,  as  to  the  completeness  or  accuracy  of such    information  and shall  have  no  liability  for   the 
consequences of use of such information.

 

 NGX Technologies reserves the right to make changes to information published in this document, at any time and without notice, 

including without limitation specifications and product descriptions. This document replaces and supercedes all information supplied 
prior to the publication hereof. 

 

 Trademarks 

 

 All referenced trademarks, product names, brands and service names are the property of their respective owners. 

 

Summary of Contents for BlueBoard Base
















Reviews: