Nexen Paper Checker PC210 User Manua Download Page 3

Page: 3 / 16

FORM NO. L-20341-E-0208

Table of Contents

THEORY OF OPERATION ------------------------------------------------------------------------------------------------------------------4

INSTALLATION -----------------------------------------------------------------------------------------------------------------------------------4

ELECTRICAL CONNECTIONS -----------------------------------------------------------------------------------------------------------6

FRONT PANEL CONTROLS & INDICATORS --------------------------------------------------------------------------------------7

SETUP CONTROLS ---------------------------------------------------------------------------------------------------------------------------8

OPERATION --------------------------------------------------------------------------------------------------------------------------------------9

CALIBRATION ---------------------------------------------------------------------------------------------------------------------------------13

SPECIFICATIONS ----------------------------------------------------------------------------------------------------------------------------15

WARRANTY-----------------------------------------------------------------------------------------------------------------------------------------

Summary of Contents for Paper Checker PC210
















