TECHNICAL DATA
A declaration of conformity is available online at www.nexa.se
MGDR-200
Power supply
220-240 V~50 Hz
Max. load
200 W
Max. load LED
3-24 W LED
Protocol
System Nexa (433,92 MHz)
Range
up to 30 m
Memory slots
32
Own consumption
< 1 W
IP classification
IP44
Dimensions
53 x 70mm
Plug-in receiver with dimmer function for earthed sockets. Works
with System Nexa remote controls, transmitters and Nexa Bridge.
The system is “self-learning”, which ensures extremely simple and
flexible installation.
INSTALLATION
Connect power to the receiver; make sure that the output does not
exceed the output stated in the table under “Technical Data”.
PROGRAMMING
1. Connect the receiver (plug-in) to an electrical socket. The receiver
will switch to programming mode as soon as current is applied.
2. Press the “ON” button for the chosen channel on any System
Nexa remote control within 6 seconds.
CONFIRMATION OF PROGRAMMING
The connected light will dim up and down two times.
DELETE MEMORY
1. To delete a memory slot, remove the receiver (plug-in) from the
wall socket.
2. Wait for at least 6 seconds.
3. Replace the receiver in a wall socket.
4. Press the “OFF” button for the selected channel on a System
Nexa remote control within 6 seconds.
To delete all memory slots, repeat steps 1–3 above and then press
the “ALL OFF” button on the System Nexa remote control within 6
seconds.
CONFIRMATION OF DELETION
The connected light will dim up and down two times.
MEMORY
Each MGDR-200 plug-in receiver has 32 memory slots. When all 32
slots are full, slot 1 will be overwritten on new programming.
CONTROL
The plug-in receive can be controlled in several ways.
1. With a System Nexa Remote Control
2. With other programmed System Nexa transmitters
3. With Nexa Smart Hub
4. With Nexa Bridge
THIS PRODUCT FEATURES SUPPORT FOR SMART MODE.
In units that support Smart Mode, up to 3 different favourite sce-
narios can be saved and then activated easily using a Nexa Smart
Mode transmitter.
DIMMER SETTINGS
The MGDR-200 is supplied set up for trailing edge phase dimming.
SETTING THE LOWEST DIMMER LEVEL
1. Remove the (plug-in) receiver from the wall socket.
2. Wait for at least 6 seconds.
3. Replace the receiver in a wall socket.
4. Press the ON button on a programmed System Nexa remote
control for 3 seconds within 6 seconds.
5. The connected light will dim up and down two times.
6. Use the programmed remote control to adjust the lowest dimmer
level. ON increases the level one step, OFF reduces the level one
step. (Four steps in all)
7. Press the ON button on a programmed System Nexa remote
control for 3 seconds to confirm the lowest dimmer level.
8. The connected light will dim up and down two times, and then
dim down to the lowest level set to confirm the new setting.
MGDR-200
Plug-in Dimmer for outdoor use
NEXA AB, DATAVÄGEN 37B, 436 32 ASKIM, SWEDEN
[email protected] | www.nexa.se
ENGLISH
SAFETY AND INFORMATION
Range indoors:
up to 30 m (optimal conditions). The range is
heavily dependent on local conditions – such as if there are any
metals nearby. For example, the heavy metal coating in low-
emission energy glass has a negative impact on the range of the
radio signals. There may be limitations on the use of the unit outside
the EU. If appropriate, check that the unit complies with the local
regulations.
Max. load:
Never connect lights or equipment that exceeds the
maximum load of the receiver. This can result in faults, short circuit
or fire.
Life-support equipment :
Never use Nexa products for life support
equipment or other devices where faults or disruptions can have
life-threatening consequences.
Disruptions:
All wireless units can be affected by disruptions that
may have an impact on performance and range. The minimum
distance between two receivers should therefore be at least 50 cm.
Repairs:
Do not attempt to repair the product. It does not contain
any serviceable parts.
Waterproofing:
The product is in a flush-proof design (IP44).
For proper outdoor function, the connected plug must be of an
approved design for outdoor use (IP44).
Cleaning:
Clean the product with a dry cloth. Do not use chemicals,
solvents or potent cleaning agents.
Environment:
Do not expose the product to extreme heat or cold,
as this may damage the electronic circuits or shorten their service
life.