Newtec SAT2200 Installation Manual Download Page 30 | Manualshive

Page: 30 / 47

background image

Terminal Installation

Satellite Terminal Installation Guide

version 2.0

- 30 -

-

Medium or high interrupted tone

The antenna points to the correct satellite but does not receive the strongest signal so far. As
soon as you hear this tone, you are sure that the antenna points to the correct satellite.

-

Low uninterrupted tone

The antenna is not pointing to a satellite or points to a wrong satellite.

«
...
28
29
30
31
32
...
»

Summary of Contents for SAT2200
















































Reviews:

No comments

Related manuals for SAT2200

Brand: Aiwa Pages: 20

Brand: Sandstrom Pages: 32

Brand: Zhong Shan Anders Electronics Pages: 5

Brand: Medion Pages: 220

Brand: Ramsey Electronics Pages: 2

Brand: Nady Systems Pages: 2

Brand: Voscom Pages: 13

Brand: B&O Play Pages: 52

Brand: dB Technologies Pages: 2

Brand: MC Crypt Pages: 65

Brand: Boss Pages: 2

Brand: Samsung Pages: 49

Brand: Samsung Pages: 65

Brand: Samsung Pages: 84

Brand: Sharp Pages: 4

Brand: Sharp Pages: 32

Brand: Sharp Pages: 48

Brand: Sharp Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands