background image

CONEX-PSD 

Two-Axis Position & Power Sensing Device 

Warranty 

Newport Corporation warrants that this product will be free from defects in material and 

workmanship and will comply with Newport’s published specifications at the time of 

sale for a period of one year from date of shipment. If found to be defective during the 

warranty period, the product will either be repaired or replaced at Newport's option. 
To exercise this warranty, write or call your local Newport office or representative, or 

contact Newport headquarters in Irvine, California. You will be given prompt assistance 

and return instructions. Send the product, freight prepaid, to the indicated service 

facility. Repairs will be made and the instrument returned freight prepaid. Repaired 

products are warranted for the remainder of the original warranty period or 90 days, 

whichever comes first. 

Limitation of Warranty 

The above warranties do not apply to products which have been repaired or modified 

without Newport’s written approval, or products subjected to unusual physical, thermal 

or electrical stress, improper installation, misuse, abuse, accident or negligence in use, 

storage, transportation or handling. This warranty also does not apply to fuses, batteries, 

or damage from battery leakage. 
 
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR 

IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY 

OR FITNESS FOR A PARTICULAR USE. NEWPORT CORPORATION SHALL 

NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, OR CONSEQUENTIAL 

DAMAGES RESULTING FROM THE PURCHASE OR USE OF ITS PRODUCTS. 
 
 

Copyright 2016

 by Newport Corporation, Irvine, CA. All rights reserved. No part of 

this manual may be reproduced or copied without the prior written approval of Newport 

Corporation. This manual is provided for information only, and product specifications 

are subject to change without notice. Any change will be reflected in future printings. 

EDH0315En1030 — 07/16

 

ii 

Summary of Contents for CONEX-PSD


























Reviews: