NewMar Phase Three PT-24-40 Installation & Operation Manual Download Page 2

U.S.A. HEADQUARTERS

P.O. Box 1306, Newport Beach, CA 92663

Phone: 714-751-0488  Fax: 714-957-1621

E-Mail: [email protected]

EURO WAREHOUSE

Phone:+31-35-603-2494

Fax:+31-35-603-2149

www.newmarpower.com

E

LECTRONIC

 P

OWER

 P

RODUCTS

C

OMMUNICATION

 

!

!

!

!

!

 N

AVIGATION

2

I)

GENERAL INFORMATION

Your Phase Three Series Battery Charger represents a new phase in charger design and
performance, employing "smart" switching circuitry which puts batteries through the opti-
mum three-step charge process, adapts for gel-cell or lead-acid batteries, features precise
voltage compensation for varying battery temperature, is rated for continuous duty and is
housed in a rugged stainless steel case.

Following is a brief listing of some of the more important features/options of your Phase
Three Charger. Each is fully detailed later in this manual:

* Three step “smart” charging: bulk, absorption, float

* Gel cell/lead-acid switch selects optimum charge/float voltages based on battery
type

* Multiple output banks charge independently based on demand

* "Universal" input of 90-264V a.c., 50-60 Hz input with no setting of selector switch
required—can be used anywhere in the world

* Current limiting prevents damage from overload

* Load activated cooling fan allows continuous operation at full-rated output

* High charge voltage time-out circuit prevents overcharge during continuous high
amperage demand

* Automatic high temp power reduction — allows continued charger operation in over-
temperature conditions at half of rated output current, avoiding complete shutdown

* Optional temperature compensation sensor (model TCS-12/24) fine tunes output
voltage based on battery temperature

* Optional remote panel (model RP) allows remote monitoring of charger phase status
and manual re-initialization of three stage charge cycle.

* Optional equalization circuit connection.

* Use as a power supply without in-line battery; allows continued use of d.c. powered
electronics (when a.c. is available) in the event that batteries must be taken off-line or
removed.

* Rugged stainless steel case with drip shield

* Carries the CE mark.

Summary of Contents for Phase Three PT-24-40

























Reviews: