NewMar Phase Three PT-24-40 Installation & Operation Manual Download Page 1

U.S.A. HEADQUARTERS

P.O. Box 1306, Newport Beach, CA 92663

Phone: 714-751-0488  Fax: 714-957-1621

E-Mail: [email protected]

EURO WAREHOUSE

Phone:+31-35-603-2494

Fax:+31-35-603-2149

www.newmarpower.com

E

LECTRONIC

 P

OWER

 P

RODUCTS

C

OMMUNICATION

 

!

!

!

!

!

 N

AVIGATION

1

INSTALLATION/OPERATION MANUAL

Models:

PT-70a

PT-24-40

CONTENTS

Section

Topic

Page

I)

GENERAL INFORMATION.................................... 2

II)

IMPORTANT SAFETY INFORMATION..................

3

III)

INSTALLATION.................................................... 5

A) Materials Provided................................. 5
B) Location................................................ 5
C) Mounting...............................................6
D) d.c. Output Wiring................................. 6
E) Multiple Unit Parallel Wiring................. 8
F) a.c. Input Wiring.................................... 8

IV)

OPERATION........................................................ 10

A) Three Stage Charge Regimen................. 10
B) Time-Out Circuit................................... 11
C) Gel-Cell/Lead-Acid Selector Switch....... 12
D) Remote Monitor Panel Option................ 13
E) Temperature Compensation Option........ 13
F) Equalize Timer Option........................... 15
G) Cooling Fan........................................... 17

V)

APPLICATION NOTES.......................................... 17

A) Start-Up................................................ 17
B) Constant Versus Occasional Use............ 18
C) Proper Load Sizing.................................18
D) Operation with Engine........................... 18
E) Operation as a d.c. Power Supply............18
      or Radar Rectifier

VI)

SPECIFICATIONS.................................................19

VII)

TROUBLESHOOTING........................................... 20

VIII)

BATTERY CARE TIPS.......................................... 22

IX)

REFERENCE APPENDIX....................................... 24

M-PT2440127
As of FEB 2003

Summary of Contents for Phase Three PT-24-40

























Reviews: