Newland EM3080-W-V2 Integration Manual Download Page 15 | Manualshive

Page: 15 / 29

background image

15

Chemical Tempering Glass

Glass offers optimal scratch and abrasion resistance. But, unannealed glass is easily broken. Chemical tempering can

greatly enhance its flexibility. Glass is

hard to be cut into different shapes and can’t be ultrasonically welded.

Coatings

Anti-reflection coatings

Anti-reflection coatings are applied for stray light control. The window with anti-reflection coatings can minimize influence

caused by the reflection. But they have high cost and terrible abrasion and scratch resistance.

Polysiloxane Coating

Polysiloxane coatings are used to prevent plastic surfaces from scratch and abrasion.

The specifications below are available if anti-reflective coating is applied. Polysiloxane coating is not needed.

«
...
13
14
15
16
17
...
»

Summary of Contents for EM3080-W-V2






























Reviews:

No comments

Related manuals for EM3080-W-V2

Brand: Magnum Pages: 54

Digital Film Scan Tool

Brand: Kodak Pages: 25

Brand: Master Pages: 18

Advanced 3D Scanner

Brand: HDI Pages: 8

Brand: Sky Light Pages: 4

SCANTEAM 2070 BASE

Brand: Hand Held Products Pages: 132

License Scanner

Brand: Abit Pages: 9

Brand: Hamlet Pages: 20

Brand: Radio Shack Pages: 73

Brand: Youjie Pages: 142

Brand: Faro Pages: 68

Brand: UMAX Technologies Pages: 21

ScanMaker 3750i

Brand: Microtek Pages: 2

Brand: Uniden Pages: 39

Bearcat UBC144XLT

Brand: Uniden Pages: 20

Brand: Launch Pages: 161

IRISPEN TRANSLATOR 6L - FLYER

Brand: I.R.I.S. Pages: 2

IRISCARD PRO 4 - FLYER

Brand: I.R.I.S. Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands