Newland BS-80 Page 150 User Manual Download

Page: 150 / 172

138

Terminating Character Suffix

Enable/Disable Terminating Character Suffix

A terminating character such as carriage return (CR) or carriage return/line feed pair (CRLF) can only be

used to mark the end of data, which means nothing can be added after it. A terminating character suffix

cannot exceed 7 characters.

Disable Terminating Character Suffix (default)

Enable Terminating Character Suffix

Set Terminating Character Suffix

To set a terminating character suffix, scan the

Set Terminating Character Suffix

barcode, the numeric

barcodes that represent the hexadecimal value of desired terminating character(s) and the

Save

barcode.

You can also quickly set the terminating character suffix to 0x0D (CR) or 0x0D,0x0A (CRLF) and enable

the transmission of it by scanning the

Terminating Character 0x0D (CR)

Terminating Character

0x0D,0x0A (CRLF)

barcode below.

Terminating Character 0x0D (CR)

Terminating Character 0x0D,0x0A (CRLF)

Set Terminating Character Suffix

Example: Set the terminating character to

“0x0A” (LF)

Scan the

Set Terminating Character Suffix

barcode.

Scan the numeric barcodes

“0” and “A” from the “

Digit Barcodes (1D Scanner)

” section in Appendix.

Scan the

Save

barcode from

the “

Save/Cancel Barcodes (1D Scanner)

” section in Appendix.

Summary of Contents for BS-80













































































































































































Search results

Summary of Contents for BS-80

Reviews:

Related manuals for BS-80

Brands by name

Popular brands

Newland BS-80, User Manual

Search results

Summary of Contents for BS-80

Reviews:

Related manuals for BS-80

Brands by name

Popular brands