background image

 

 

4. SUPPLIED ACCESSORIES 

 

SIB 16x40 Gyro is supplied in the following assembly: 

 

- Device 
- Objective lens caps 
- Carrying case 
- Neck strap 
- Hand strap 
- DC regulator 
- User’s manual 
- Warranty card 
Optional accessories: 
- Amber filters (optional) 
-

 

Night vision eyepieces (optional) 

 

1 pc. 
2 pc. 
1 pc. 
1 pc. 
1 pc. 
1 pc. 
1 pc.  
1 pc.  
 
2 pc. 
2 pc. 

 

5. OPERATION INSTRUCTIONS

 

 

5.1. Preparing the Device for Operation without Image 

Stabilization 

 

1.

 

Remove the device from the case and adjust neck strap (7) 
and hand strap (1) (fig. 1).  

2.

 

Remove the protective caps from the objective lenses and, if 
necessary, mount the optional light filters.  

3.

 

Adjust the interpupillary distance-using lever (9).  

4.

 

Adjust the dioptric correction by rotating rings on the eyepieces (8).  

5.

 

Now the device can operate as a conventional 16x 
magnification binocular.  

 

 

5.2. Preparing the Device for Operation with Image 

Stabilization 

 

 

1.

 

Put the lens caps on the objective lenses. Take the power 
supply unit in your left hand.  

2.

 

Pull out pin (3) on the power supply unit (fig. 2) and 
disconnect the power supply unit from the device with an 
easy movement towards you.  

3.

 

Insert six AA batteries into the cartridge (1) (fig. 2) 
observing correct polarity.  

4.

 

Mount the cartridge with batteries into the power supply unit 
(2) (fig. 1) and secure it by cramp (4) (fig. 2).  

5.

 

ATTENTION! To avoid damage of the cramp, while 
mounting the cartridge into the power supply unit, particular 
attention must be drawn to its position respecting to the body 
of the power supply unit. While the cartridge is being 
mounted into the power supply unit, the cramp should be 
placed above the cartridge.  

6.

 

In order to connect the power supply unit to the device, pull 
out pin (3) with an easy movement in the direction away 
from you and then release the locator to bring the power 
supply unit against the delimiter. Turn on the device by 
setting supply voltage switch (4) (fig. 1) to ON position and 
check the power supply unit for proper operation (indicator 
(3) must glow brightly).  

 
 

 

Summary of Contents for SIB 16x40 GR









Reviews: