background image

 
 
 

 
 
 
 
 

Head Office 

6  Wincomblee   Road 
Walker  Riverside 
Newcastle upon Tyne 
NE6  3PF 
 
Tel: +44 (0)191 295 0111 
Fax: +44 (0)191 295 0077 
Website: 

www.newarc.co.uk

 

e-mail:   

[email protected]

 

Aberdeen Office 

Unit 23  Kirkhill  Place 
Kirkhill  Industrial  Estate, Dyce 
Aberdeen 
AB21 0GU 

 
Tel: +44 (0)1224  771063 
Fax: +44 (0)1224  724536 

 

Guarantee 

New-Arc  Equipment  Ltd  warrants  that  its  goods  and  services  are  guaranteed  to  meet  the  specific 
performance  under  the  stated  conditions  of  use.  New-Arc  cannot  be  held  responsible  for  general 
wear  and  tear  or  for  failure  occurring  due  to  misuse  or  abuse  arising  out  of  circumstances  outside 
the stated conditions of use. The stated conditions of use are that considered normal industrial prac-
tice and are not exhaustive. Each machine is identified with a unique serial number and accompa-
nied with the guarantee. New-Arc reserve the right to  a) Repair. b) Replace. c)  Authorise the rea-
sonable  cost  of  repair  or  replacement  at  an  approved  New-Arc  service    agent.  d)  Credit  for  any 
purchased equipment  (less reasonable depreciation for actual use and condition) at its entire dis-
cretion. This in no way affects your rights as a consumer. The guarantee is enclosed with each ma-
chine.  
 

 
Waiver 

Whilst  every  endeavor  is  made  to  ensure  the  details  of  this  document  are  correct  at  the  date  of 
print. New-Arc accepts no liability for correctness in respect of any impending change in legislation 
or health and safety requirements. New-Arc also reserve the right to amend the detail of the docu-
ment content without any notification to the consumer. If reference is made to New-Arc while utilis-
ing the document for spare parts purchase or instruction please advise the revision of the document 
to ensure correctness of information.  

 

Summary of Contents for R2500













Reviews: