Newage Outdoor Kitchen SS 64

GARANTIE LIMITÉE:

Tous les produits doivent être installés, utilisés et entretenus conformément aux directives qui les accompagnent. 
Si un produit ayant été correctement installé, utilisé et entretenu ne répond pas aux conditions de la garantie 
limitée ci-dessous, NewAge Products, Inc. (« NewAge ») remplacera les pièces ou le produit défectueux.

Sous réserve des limitations et des exclusions énoncées ci-dessous ou dans la documentation d’un autre produit, 
NewAge garantit à l’acheteur initial que (1) les surfaces du produit seront exemptes de défaut pendant trois ans 
après la date d’achat, (2) les glissières de tiroir seront exemptes de défaut pendant deux ans après la date d’achat, 
et (3) l’intégrité structurale générale du produit (à l’exception des surfaces et des glissières de tiroir) sera exempte 
de défaut pendant dix ans après la date d’achat. 

Le client devra payer les coûts d’expédition associés au remplacement du produit ou des pièces. La présente 
garantie limitée vise uniquement le remplacement du produit. NewAge ne saurait en aucune circonstance être 
tenue responsable de dommages particuliers, indirects ou consécutifs.

La présente garantie limitée est off erte à l’acheteur initial seulement, et n’est pas transférable. NewAge pourra, à 
sa discrétion exclusive, exiger la présentation de la preuve d’achat et de renseignements supplémentaires con-
cernant la défectuosité. La garantie vise uniquement les produits vendus sur le territoire continental des États-
Unis, au Canada et au Royaume-Uni.  

EXCLUSION DE TOUTE AUTRE GARANTIE

LES AUTRES GARANTIES QUELLES QU’ELLES SOIENT SONT EXCLUES DANS TOUTE LA MESURE PERMISE PAR 
LES LOIS APPLICABLES. SANS RESTREINDRE LE CARACTÈRE GÉNÉRAL DE CE QUI PRÉCÈDE, NEWAGE EXCLUT 
EXPRESSÉMENT TOUTE GARANTIE IMPLICITE DE QUALITÉ MARCHANDE OU DE CONVENANCE PRÉCISE.

NEWAGE PRODUCTS INC. NE PAIERA PAS LES FRAIS ASSOCIÉS AUX CIRCONSTANCES SUIVANTES :

1.

Les visites de réparateur ou les frais de main-d’œuvre;

2.

Les produits endommagés par accident, mésusage, mauvais traitement, incendie, inondation, installation

incorrecte, catastrophe naturelle, négligence, corrosion, entretien ou nettoyage incorrects, modifi cation,

manipulation sans précaution ou non-respect des directives d’entretien;

3.

Les produits endommagés par une charge supérieure à la capacité de poids maximale énoncée dans les
directives qui accompagnent le produit;

4.

Les défectuosités résultant d’une utilisation excessive par rapport à l’utilisation résidentielle normale;

5.

Les dommages esthétiques survenus après l’achat du produit, y compris les égratignures, les creux, les

bosses, la corrosion ou les taches qui ne modifi ent en rien l’intégrité structurale

ou les fonctions du produit;

6.

Les pertes de contenu du produit.

Summary of Contents for Outdoor Kitchen SS 64" Prep Table



















Reviews: