New lift FST Manual Download Page 154

Page: 154 / 174

6 Error List
6.3 Event messages

152

FST_HB.EN04/03

6.3 Event messages

Code

Message

Description

Reason

128

COLDSTART

Power supply of the FST was
interrupted and is back on.

The FST-Controller was
switched off and on again on
the fuse or the main switch.

There was a power failure.

129

INSPECTION–ON

INSPECTION–OFF

Inspection work is being carried out.

The inspection switch on the car
roof is set to INSPECTION.

131

POWER LOST

Failure of the 24V power supply.

The system has been shut down
or the power supply is faulty.

132

REMOTE RESET

The FST-Controller has been reset
by the GST Group Controller.

The FST-Controller has been
reset through the serial interface.

133

CALIBRATION–START

CALIBRATION–OK!

Calibration progress is displayed.

A calibration drive has been
triggered.

134

LEARN DRIVE–START

LEARN DRIVE–OK!

Learn drive progress is displayed.

A learn drive has been triggered.

135

SOFTWARE UPDATE

The software of the FST has been
updated with a PC-Card.

136

EVACUATION–ON

EVACUATION–OFF

EVACUATION–OK

An evacuation drive has been
carried out.

The evacuation signal on a
programmable input/output has
been active.

137

X12-SERIAL OK

DCP interface X12 in operation.

The serial DCP interface X12
between FST and frequency
converter has been initialised
correctly (e.g. after switching
on).

138

MONITOR SIGNAL–ON

MONITOR SIGNAL–OFF

State change on the programmable
“Monitor” input.

The programmable “Monitor”
input has changed its state. This
input can be used to enter state
changes of any signal in the error
storage (see “Programmierbare
Ein-/Ausgänge” on page 155).

139

APRON OUT–ON

APRON OUT–OFF

State change on the “Apron
Monitoring” input.

The state of the electronically
monitored apron for small shaft
pits is entered in the error
storage as a message.

Summary of Contents for FST















































































































































































Search results

Summary of Contents for FST

Reviews:

Related manuals for FST

Brands by name

Popular brands

New lift FST, Manual

Search results

Summary of Contents for FST

Reviews:

Related manuals for FST

Brands by name

Popular brands