background image

 

 

 

 

 

 

 

 

 

 

 

 
 

            1.  NEVER put your hands inside the machine as it may lead to bodily injury. 
 
            2.  DON’T perforate materials other than paper as this might damage internal parts. 
 
            3.  DON’T disassemble or modify the unit, otherwise injury or electrical shock may occur. 
 
            4.  BE SURE to detach the power cord from the outlet before relocating the machine. 
 
            5.  KEEP the unit out of children’s reach and do not let them operate it, otherwise injury may occur. 
 
            6.  ALWAYS detach the power cord from the outlet if the unit is not to be used for extended periods. 

                   

C

C

a

a

u

u

t

t

i

i

o

o

n

n

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

   

S

S

a

a

f

f

e

e

t

t

y

y

 

 

 

P

P

r

r

e

e

c

c

a

a

u

u

t

t

i

i

o

o

n

n

s

s

 

 

 

 

To ensure safe use of the machine and avoid damage to it, 
please be sure to observe the following precautions.

 

 

 

Keep your fingers and hands away from the  die  block  when  perforating, otherwise injury may occur.

 

 

Don’t touch moving parts when perforating, otherwise injury may occur.

 

 

Don’t pull the paper out while perforating. Wait until perforation cycle is completed.

 

 

DON’T disassemble or modify the unit as it might cause a machine malfunction, possible injury, 
fire  or  electric  shock  etc.

 

 

DON’T perforate materials other than paper such as metals:

 

iron,  copper,  aluminum,  stainless 

steel, etc.  This may result in damage to the die block and void manufacturer warranty.

 

 

DON’T perforate materials which adhere to the paper such as staples, paper clips, adhesive tape, etc. 
This may result in damage to the die block and void manufacturer warranty.

 

 

DON’T perforate items such as wet paper, adhesion stickers, vinyl, etc. as these could cause 
paper chips to clog the die block.

 

 

Perforated paper chips will accumulate in waste receptacle with frequent use of the perforator. Empty 
it at regular intervals. Not emptying the waste will cause the paper particles to build up in the die block. 

 

Please be sure to remove the plug from the outlet when removing the paper waste. 

 

DON’T  install  the  machine  on  an  uneven  or  unstable  surface  as  it  could  become  susceptible 
to  falling  off. 

 

If  you  must  move  the  machine,  please  carry  it  by  the  bottom  of  the  main  body  with  both  hands. 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for 112-605

















Reviews: