background image

INTRODUCTION

Do organise work practices and protective clothing to avoid soling of the skin and eyes, breathing vapors / aerosols /
dusts / fumes, inadequate container labelling; fire and explosion hazards.

Do wash before job breaks, before eating, smoking, drinking or using toilet facilities when handling chemical materials.

Do keep work areas clean, uncluttered and free of spills.

Do store according to national and local regulations.

Do keep chemical materials out of reach of children.

Do not’s

Do not mix chemical materials except under the manufacturers’ instructions. Some chemicals can form other toxic or
harmful chemicals give off toxic or harmful fumes be explosive when mixed together.

Do not spray chemical materials, particular those based on solvents, in confined spaces. E.g. When people are inside
a vehicle.

Do not apply heat or flame to chemical materials except under the manufacturers’ instructions. Some are highly
inflammable and some may release toxic or harmful fumes.

Do not leave containers open. Fumes given off can build up to toxic, harmful or explosive concentrations. Some
fumes are heavier than air and will accumulate in confined areas, pits etc.

Do not transfer chemical materials to unlabeled containers.

Do not clean hands or clothing with chemical materials. Chemicals, particularly solvents and fuels will dry the skin
and may cause irritation with dermatitis. Some can be absorbed through the skin in toxic or harmful quantities.

Do not use emptied containers for other materials, except when they have been cleaned under supervised conditions.

Do not sniff or smell chemical materials. Brief exposure to high concentrations of fumes can be toxic or harmful.

Clutch fluids

See brake and clutch fluids.

Clutch linings and pads

See brake and clutch linings and pads.

Corrosion protection materials

See solvents, fire.

Highly flammable, flammable.

These materials are varied and the manufactures’ instructions should be followed. They may contain solvents, resins,
petroleum products etc. skin and eye contact should be avoided. They should only be sprayed in conditions of ade-
quate ventilation and not in confined spaces.

Cutting

See welding.

De-waxing

See solvents and fuels (kerosene).

47866580 11/12/2015

9

Summary of Contents for TT4.80










































Reviews: