background image

SECTION 10 -- ENGINE -- CHAPTER 1

13

(continued)

12. DELIVERY PROGRESSION

Rpm

LDA pressure

kPa

Delivery per 1000 shots: cm

3

(gal.)

1300

100

0 to 3.0 (0 to 0.0008)

1200

100

47.5 to 63.5 (0.01254to 0.0168)

700

100

88 to 93 (0.0232 to 0.0246)

600

42.5

82.8 to 90.8 (0.0219 to 0.0240)

500

0

78.2 to 83.2 (0.0207 to 0.0220)

1150

100

74.6 to 80.6 (0.0197 to 0.0213)

500

100

89.5 to 96.5 (0.0236 to 0.0255)

13. ZERO CAPACITY (STOP)

Rpm:

325

Voltage (volts):

0

Delivery per 1000 shots: cm

3

0 to 3.0

(gal. 0 to 0.0008)

14. DELIVERY CHECK AT IDLE SPEED

Rpm

325

410

Delivery per 1000 shots:

cm

3

(gal.)

3.5 to 14.5

(0.0009 to 0.0038)

0 to 3.0

(0 to 0.0008)

Note: the values shown above in brackets must be used for checking purposes only.

15. AUTOMATIC START CAPACITY SUPPLEMENT

Rpm

Delivery per 1000 shots: cm

3

(gal.)

100

85 to 125 (0.0225 to 0.0330)

250

71 to 91 (0.0188 to 0.0240)

160

100 to 130 (0.0264 to 0.0343)

BENCH TEST PERFORMANCE DATA

Test conditions

Fixed advance before TDC cylinder No.1 in compression stroke:

(see previous page)

Relative humidity 70

o

/

o

±

5.

Engine without fan, air filter and exhaust silencer.

Ambient temperature

25

o

±

3

o

C (77

o

±

37.4

o

F).

Atmospheric pressure 990

±

10 mbar (14.36

±

0.15 psi).

Specific gravity of diesel fuel

840 g/l. (7 lb./gal.)

Throttle

l

B ki

l d

li d

Engine

speed

Power output with engine run--in for a total of:

Fuel

consumption

lever

position

Braking load applied

rpm

2 hours

kW (hp)

50 hours

kW (hp)

kg/h (lb./h)

Maximum

For maximum

power output

2300

50.4 (68.5)

51.4 to

 

54.5 (1)

(69.9 to

 

74.1)

11.9 to 12.6

(26.24 to

27.78)

Maximum

For maximum

torque

1400

40.8 (55.4)

41.6 to

 

44.2 (2)

(56.6 to

 

60.1)

9.1 to 9.6

(20.06 to

21.16)

Maximum

None (no--load)

2475 to

2525

--

--

--

Minimum

None (no--load)

625 to 675

--

--

--

Note: Air delivery pressure (1) bar 0.95 to 1.1 (psi 13.8 to 16) -- (2) bar 0.55 to 0.65 (psi 8 to 9.4).

Summary of Contents for TN55










































Reviews: