background image

INTRODUCTION

Basic instructions

PERIODIC MAINTENANCE TABLE

Item / Frequency

Every 10 h or daily

Every 50 h or daily

After the planting season

Grease all grease fittings.

X

Calibrate the tires

X

Re-tighten bolts and nuts in
general

X

For a new machine, do the
tightening daily, throughout

the first week.

Check the transmission
chains: clean them,
lubricate them and adjust
the tension.

X

Perform a general washing
of the machine and protect
the metal parts with oil

X

ATTENTION:

Read and follow the safety recommendations regarding maintenance contained in this Section of the

Manual.

GREASING

• Recommended grease:

Use Lithium-based grease

only, NLGI-2 grade.

• Lubricate all fittings every 10 h or daily.

• There are grease fittings with different angles to facili-

tate access: straight fitting

0 °

- inclined

45 °

and

90 °

-

see figure.

• Avoid excess grease: the correct amount to be applied

is reached at the time the old grease begins to seep out
of the housing.

• Damaged grease fittings should be replaced immedi-

ately to avoid compromising the greasing of the respec-
tive fitting.

• Before greasing, clean the grease fittings to avoid the

penetration of dust in lubricated components (bearings
and bushings).

• Wheel hubs

(1)

: it is recommended that at the be-

ginning of each season the hubs are disassembled,
cleaned and checked: replace the seals and other com-
ponents as needed.
Then, make the adjustment of the pre-load of the bear-
ings (see

Transport wheel Axle - Overview (44.530)

of this manual) and lubricate with new grease.

BAIL14TR00455AB

1

BAIL14SE00802AI

2

CHAINS AND GEARS

There are two different ways to adjust the chains in Seed-
ers:

47918064 10/09/2015

14

Summary of Contents for PS2030






















Reviews:

Related manuals for PS2030