New Holland FR450 TIER 3 Service Manual Download

Page: 35 / 81

INTRODUCTION

Product identification

EXPLANATION OF MACHINE SERIAL NUMBERS

Example : n° 615848002

615848001: The first two digits identify the model within a product line:

FR450 (Tier 3 units) = 51

FR450 (Tier 4 units) = 61

FR500 (Tier 3 units) = 52

FR500 (Tier 4 units) = 62

FR600 = 53

FR700 = 54

FR850 = 55

61 5848002: The third digit indicates the product line.

CR-CX-CS-CSX Combine Harvesters:

TC Combine Harvesters:

Combine Headers:

Forage Harvesters:

Grass Pickup:

Square Balers:

615 848002: These three digits indicate the batch in which the machine was made.

61 5848002: Product line number 5 and batch 848 together form the series number.

615848 002: The last 3 digits are a sequential number for each model within a batch.

Summarizing we can say that this machine is a Tier 4 unit and the second FR450 of series 5848.

47812470 23/02/2015

Summary of Contents for FR450 TIER 3


















































































Search results

Summary of Contents for FR450 TIER 3

Reviews:

Related manuals for FR450 TIER 3

Brands by name

Popular brands

New Holland FR450 TIER 3, Service Manual

Search results

Summary of Contents for FR450 TIER 3

Reviews:

Related manuals for FR450 TIER 3

Brands by name

Popular brands