New Holland E75CSR Service Manual Download | Manualshive

Page: 10 / 51

background image

INTRODUCTION

Safety rules

ATTENTION:

Do not operate or perform any maintenance on this machine until all instructions found in the OPERA-

TOR’S MANUAL and this MANUAL have been thoroughly read and understood. Improper operation or maintenance
of this machine may cause accidents and could result in serious injury or death.
Always keep the manual in storage.
If it is missing or damaged, place an order with an authorized our Distributor for a replacement. If you have any
questions, please consult an authorized our Distributor.

1. Most accidents, which occur during operation, are due to neglect of precautionary measures and safety rules.

Sufficient care should be taken to avoid these accidents. Erroneous operation, lubrication or maintenance ser-
vices are very dangerous and may cause injury or death of personnel. Therefore all precautionary measures,
NOTES, DANGERS, WARNINGS and CAUTIONS contained in the manual and on the machine should be read
and understood by all personnel before starting any work with or on the machine.

2. Operation, inspection, and maintenance should be carefully carried out, and safety must be given the first priority.

Messages of safety are indicated with marks. The safety information contained in the manual is intended only to
supplement safety codes, insurance requirements, local laws, rules and regulations.

3. Messages of safety appear in the manual and on the machine : All messages of safety are identified by either

word of "DANGER", "WARNING" and "CAUTION".

1. Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury and is represented as follows:

2. Indicates a potentially hazardous situation which, if not avoided, could result in death
or serious injury and is represented as follows:

3. Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury. It may also be used to alert against possible damage to the machine and
its components and is represented as follows:
4. It is very difficult to forecast every danger that may occur during operation. However,
safety can be ensured by fully understanding proper operating procedures for this
machine according to methods recommended by Manufacturer.
5. While operating the machine, be sure to perform work with great care, so as not to
damage the machine, or allow accidents to occur.
6. Continue studying the manual until all Safety, Operation and Maintenance procedures
are completely understood by all persons working with the machine.

47488366A 13/03/2013

5

Find manuals at https://best-manuals.com

«
...
8
9
10
11
12
...
»

Summary of Contents for E75CSR




















































Reviews:

No comments

Related manuals for E75CSR

Brand: Cambridge Elevating Pages: 21

Brand: Yuchai Pages: 145

Brand: Galeo Pages: 299

Brand: VMB Pages: 26

Brand: Terex Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands