New Holland CR8.90 Service Manual Download Page 75

Page: 75 / 81

Engine - Air cleaners and lines

Air cleaner - Cleaning

CR6.80 TIER 4B

CR6.90

CR7.90

CR8.90

CR9.90

1. The filter element should only be cleaned when there is

an alarm stating "Air filter blocked" (625 mm) (24 - 5/8"
vacuum)" on the display monitor in the cab.

NOTE:

Illustration is for reference only. Part may look dif-

ferent, depending on model.

2. To remove the air cleaner element, remove cover by

loosening clamps

(1)

20030145

3. Remove the primary filter

(1)

from housing. Do not let

dirt fall on the safety filter.

NOTICE:

Do not remove safety element unless it is to be

replaced.

50030146

4. To clean the element, hold the top and tap it against the

palm of the other hand to remove the dust. Never tap
it on a hard surface or you can damage the filter.

5. When tapping does not remove the dirt, direct com-

pressed air through the element, from the inside to-
wards the outside.

NOTE:

Never blow compressed air from the outside to the

inside of the filter because particles can become embedded
or lodged in the filter and later be released into the engine
causing damage.

6. To prevent damage to the element when cleaning

with compressed air, take the following precautions:
1) Maximum air pressure should not exceed

5 bar

(

72.5 psi

2) Move the nozzle up and down when rotating the
element.
3) Keep the nozzle at least

25 mm

(

1 in

) from the

pleated paper.

NOTE:

To keep the interval acceptable, it is highly recom-

mended to clean the element with compressed air.

_47865347 25/04/2015

10.2 [10.202] / 11

Summary of Contents for CR8.90


















































































Search results

Summary of Contents for CR8.90

Reviews:

Related manuals for CR8.90

Brands by name

Popular brands

New Holland CR8.90, Service Manual

Search results

Summary of Contents for CR8.90

Reviews:

Related manuals for CR8.90

Brands by name

Popular brands