New England Arbors Dublin Assembly Instructions Download Page 1

1.

Post Caps

 (6)

 - 10600

2.

Arches

 (4)

 - 10702-1

3.

Arch Rafters 

(6)

 

- 10757

4.

Left Posts 

(2) 

- 10760-1

5.

Side Panel Top Horizontal Rails 

(2)

 - 10751-1

6.

Side Panel Bent Vertical Spindles (46.6 in. / 118.4 cm.) 

(4)

 - 10762-1

7.

Side Panel Middle Straight Vertical Spindles (45.5 in. / 115.6 cm.) 

(2)

 

- 10763-1

8.

Side Panel Middle Horizontal Rails 

(2)

 - 10754-1

9.

Right Posts 

(2) 

- 10761-1

10.

Side Panel Bottom Horizontal Rails

 (2)

 

- 10755-1

11.

Ground 

Mounting Extensions 

(4) 

- 10845

12.

5/8 in. (16

 

m

m

) Self-Augering Screws 

(

32

)

 - 20016

 

13.

1 1/4 in. (32 mm) Self-Augering Screws (16)

 - 20047

 

Tools You Will Need

• Cordless Drill
• Level
• Stool or Short Ladder
• Shovel
• Cement (For Installation)

Assembly Time

• Approximately 30 minutes 

(2 People)

General Information

   

Read Instructions through carefully before beginning assembly.

    •  When assembling components, place on a non-abrasive surface

         (i.e. shipping box) 

to avoid scratching. 

• We recommend an area approx 10 ft. x 8 ft.

 

(3 m x 2.

4

 m )

 for

 

unobstructed assembling.

• You should not need to use excessive force when assembling components.

Please read through before starting assembly.

IMPORTANT:  CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS.

Check Box for These Contents 

In the event of missing or defective parts please call our customer service dept. at 1 800 282 9346 (Mon. to Fri. 8:00 AM to 4:00 PM EST).

(UK Tel: (44) 2038 687160 (Mon. to Fri.  1:00 PM to 10:00 PM GMT).

ASSEMBLY INSTRUCTIONS

The Dublin Arbor / Arch

1

42 in.

(107 cm)

18 in.

(46 cm)

82 in.

(208 cm)

46 in.

 (117 cm)

12

Not to Scale

8

7

6

5

2

3

1

11

10

45 in.

(114 cm)

9 in.

 (23 cm)

21 in.

(53 cm)

4

9

V3.

3

/

0817

17

www.newenglandarbors.com 

www.newenglandarbors.co.uk

1

3

Summary of Contents for Dublin

Page 1: ...tion Read Instructions through carefully before beginning assembly When assembling components place on a non abrasive surface i e shipping box to avoid scratching We recommend an area approx 10 ft x 8 ft 3 m x 2 4 m for unobstructed assembling You should not need to use excessive force when assembling components Please read through before starting assembly IMPORTANT CHECK THE INSIDE OF YOUR POSTS ...

Page 2: ...ost caps at bottom of arch Fig 2 and repeat for other arch Insert arch rafters 6 into the holes on the arches until they bottom out inside the arches There are locking tabs located at each end of the rafters that once inserted into the holes will lock into place The Dublin Arbor Arch Assemble the Arch System 3 3 4 1 1 Fig 2 2 Fig 1 2 PLEASE NOTE Arch rafters have locking tabs located at both ends ...

Page 3: ...to place the two outer vertical spindles The assembled side panel will need to be held together until it is inserted into the post Lay out one LEFT post as identified horizontally with holes facing up and insert the assembled side panel by aligning the horizontal rails with the holes on the post Lay out one RIGHT post as identified horizontally with holes facing up and insert the assembled side pa...

Page 4: ...the holes with wet cement flush to the ground You will need 2 bags of pre mix concrete purchase separately Carefully move the arbor back into position Support the arbor and level over the holes with bricks stones or blocks of wood under the bottom rail of the side panel The post bottoms should insert themselves approximately 1 1 5cm into the concrete Allow the concrete to set 1 2 3 B Into Earth Wi...

Reviews: