Página -
17 -
HINTS FOR BETTER RECEPTION
2. THE RECEIVER HAS A BUILT-IN FM WIRE ANTENNA HANGING AT THE REAR CABINET. THIS WIRE
SHOULD BE TOTALLY UNRAVELED AND EXTENDED FOR BEST RECEPTION.
FM & FM-STEREO RADIO ENCODING
8. PRESS
TUNER BUTTON
TO ACTIVATE “TUNER” MODE.
9. INSERT MEMORY DEVICE (USB DRIVE, SD OR MMC CARD)
10. PRESS THE
REC
BUTTON, IT WILL TAKE 3-5 SECONDS TO READ MEMORY DEVICE. THEN USB OR SD
ICON WILL BE FLASHING.
11. PRESSING
SKIP UP
OR
SKIP DOWN
BUTTON
TO SELECT DESIRED MODE (USB OR SD) FOR
ENCODING. THEN PRESS THE
REC
BUTTON AGAIN TO CONFIRM.
AND THE SYSTEM IS
STARTING THE ENCODING MODE AFTER FEW SECONDSS.
12. IF ONLY USB DRIVE, SD OR MMC CARD IS INSERTED, STEP 4 CAN BE SKIPPED.
13. THE USB OR SD ICON WILL BE FLASHING ON THE DISPLAY DURNIG ENCODING.
14. TO FINISH ENCODING, PRESS
STOP
BUTTON
AND DISPLAY WILL SHOW “END” AND RETURN TO
“ TUNER” MODE.
REMARK:-
-
THE RECORDING SPEED IS 1:1 AND ACCORDING TO THE ACTUAL PLAYING TIME OF FM OR FM-ST
RADIO
-
THE RECORDING FORMAT IS PRESET AT – MP3
BIT RATE : 128 KBPS
-
DURING FM & FM-STEREO RADIO ENCODING, RADIO FREQEUNCY IS FXIED AND CANNOT BE TUNED
PHONO & ENCODING
NOTED:
-
REMOVE THE STYLUS PROTECTOR.
-
BE SURE THAT THE TONE ARM IS BEING DETACHED FROM THE TONE ARM
REST BEFORE OPERATING AND RE-SECURED AGAIN AFTERWARDS.
10. PRESS
PHONO
BUTTON TO SELECT “PHON” ON DISPLAY.
11. SET THE
SPEED SELECTOR
TO THE PROPER POSITION DEPENDING ON THE RECORD TO BE PLAYED.
12. PLACE THE RECORD ON THE PLATTER, USE THE 45 RPM ADAPTOR IF REQUIRED.
13. PUSH THE
LIFT LEVER
UPWARD TO RAISE THE TONE ARM FROM THE ARM PARK,
AND THEN SLOWLY MOVE IT TO THE RECORD SIDE. THE PLATTER WILL START TO
ROTATE.
14. PUT DOWN THE
LIFT LEVER
TO DROP THE TONE ARM AND TOUCH THE RECORD
GENTLY. PHONO PLAYING STARTS NOW.
15.
PUSH THE
LIFT LEVER
UPWARD TO RAISE THE TONE ARM FROM THE ARM PARK,
NOW PLATTER WILL STILL BE ROTATING BUT PHONO PLAYING WILL STOP. TO CONTINUE THE PLAYING,
THE USER NEEDS TO PUT DOWN THE
LIFT LEVER.
16. ADJUST THE VOLUME TO THE DESIRED LEVEL.
17. AT THE END OF RECORD, THE PLATTER WILL AUTOMATICALLY STOP ROTATING. PUSH THE
LIFT LEVER
UPWARD TO RAISE THE TONE ARM AND MOVE IT TO THE ARM PARK, AND THEN PUT DOWN THE
LIFT
LEVER
.
18. TO STOP MANUALLY, LIFT THE TONE ARM FROM THE RECORD AND RETURN IT TO THE ARM PARK.
REMARK
: AS SOME KIND OF RECORD THE AUTO-STOP AREA WAS OUT OF THE UNIT SETTING, SO IT WILL
STOP BEFORE THE LAST TRACK FINISHES. IN THIS CASE, SELECT THE
AUTO-STOP SWITCH
TO “ OFF
“ POSITION, THEN IT WILL RUN TO THE END OF THE RECORD BUT WILL NOT STOP AUTOMATICALLY (TURN
OFF THE UNIT BY POWER BUTTON OR SWITCH BACK THE
AUTO-STOP SWITCH
TO “ ON “ POSITION TO
STOP THE PLATTER ROTATE). THEN PUT BACK THE TONE ARM TO THE ARM PARK.
PHONO ENCODING
1. PRESS
PHONO
BUTTON TO ACTIVATE “PHON” ON DISPLAY AND THEN INSERT MEMORY DEVICE (USB
DRIVE, SD OR MMC CARD).
2.PRESS THE
REC
BUTTON, IT WILL TAKE 3-5 SECONDS TO READ MEMORY DEVICE. THEN USB OR SD ICON
WILL BE FLASHING.
3. PRESSING
SKIP UP
OR
SKIP DOWN
BUTTON
TO SELECT DESIRED MODE (USB OR SD) FOR
ENCODING. THEN PRESS THE
REC
BUTTON AGAIN TO CONFIRM.
AND THE SYSTEM IS STARTING
THE ENCODING MODE AFTER FEW SECONDSS.
