background image

 

 

12 

8. Important Maintenance Instruction 

Kindly pay attention to the following in order to achieve the best maintenance of the product: 

  Keep the device dry. Rain, moisture, or any liquid might contain minerals and thus corrode   

electronic circuits. If the device gets wet, please dry it completely. 

  Do not use or store the device in dusty or dirty environment. It might damage its detachable parts   

and electronic components. 

  Do not store the device under excessive heat condition. High temperature can shorten the life of   

electronic devices, destroy batteries, and deform or melt some plastic parts. 

  Do not store the device in places that are too cold. Otherwise, when the temperature rises to   

normal temperature, moisture will form inside, which will destroy the board. 

  Do not throw, knock or shake the device. Rough handling of equipment can destroy internal   

circuit boards and delicate structures. 

  Do not clean the device with strong chemicals, detergents or strong detergents. 

  Do not apply the device with paint. Smudges might block in the device and affect the operation. 

  Do not throw the battery into the fire, or the battery will explode. Damaged batteries may also   

explode. 

 

All of the above applies to your device, battery and accessories. If any device is not working 

properly, please take it to the nearest authorized service facility for repair. 

 

Summary of Contents for R718WA














Reviews: