July 2012
This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste
Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European Union,
this product should be treated and recycled in accordance with the laws of your jurisdiction
implementing the WEEE Directive.
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered
trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is
subject to change without notice. Other brand and product names are registered trademarks or trademarks of
their respective holders. © 2012 NETGEAR, Inc. All rights reserved. For indoor use only in all EU countries and
Switzerland.
Port Status,
Ports 9–16
(left LED)
On
A 100 M link has been successfully established on the port.
Blinking
The port is transmitting or receiving data.
Off
No link.
Port Status,
Ports 9–16
(right LED)
On
A 10 M link has been successfully established on the port.
Blinking
The port is transmitting or receiving data.
Off
No link.
Frame forward rate
14,800 frames/sec max. for 10 M port; 148,800 frames/sec max.
for 100 M port.
Network latency (64-byte
packets)
100 – 100 Mbps: 20
μ
s max.
Address database size
8 K MAC addresses
Queue buffer
1.25 Mbit
Standards compatibility
IEEE 802.3i 10BASE-T Ethernet, IEEE 802.3u, 100BASE-
TX Fast Ethernet, IEEE 802.3x Flow Control, IEEE 802.3af
Power over Ethernet; IEEE 802.1p priority tags; compatible
with Windows®, Mac®OS, NetWare®, Linux®
Network interface
RJ-45 connector for 10BASE-T or 100BASE-TX Ethernet
Interface
Power
69.6W max. and 48V @ 1.45A DC input
Port description
10/100 Mbps Auto Uplink™ RJ45 ports with PoE enabled
(Port 1 – Port 8)
10/100 Mbps Auto Uplink™ RJ45 ports (Port 9 – Port 16)
PoE power budget
55W max. (all PoE ports, Port 1 – Port 8), 15.4W max. per
PoE port
Dimensions
287 x 103 x 27 mm (11.3 x 4.1 x 1.1 in.)
Weight
0.9 kg (2.0 lbs)
Operating temperature
0° to 40° C (32° to 104° F)
Operating humidity
10% to 90% relative humidity, non-condensing
Electromagnetic compliance
CE Class A; FCC Part 15, Class A; VCCI Class A;
C-Tick Class A
Safety agency approvals for
the power adapter
CE/LVD, CB
Performance Specifications
LED
Status
Description
PoE example 1
: 4 PDs are connected to FS116P (Port 1 – Port 4) consuming 50W,
leaving 5W of power available. The PoE MAX LED lights. There is less than 7W
available. The FS116P does not provide power to any new connected PD. The 5W
remaining is reserved for power surges by the original PD devices.
PoE example 2
: Port 1– Port 4 all have PDs drawing 13W, for a total of 52W. Since
the remaining power is less than 7W, the PoE MAX LED lights. If all of the PDs
surge to 14W, exceeding the power budget (55W), Port 4 stops providing power
since it has the lowest priority of the ports providing power. The power from Port 4 is
allocated to the other ports. If the ports are plugged in at the same time, priority is
based on port number. The PoE status LED for Port 4 turns yellow, and the PoE
MAX LED turns off, since there is now more than 7W available.
Technical Specifications
Troubleshooting
Check that are using the NETGEAR power adapter supplied with your switch.
The Power LED is not lit.
The switch has no power.
•
Make sure that the power cord is correctly connected to the switch.
•
Make sure that the power adapter is connected to a functioning power outlet. If it
is in a power strip, make sure that the power strip is turned on. If a light switch
controls the socket, make sure that the switch is in the on position.
The Port LED for a connected device is not lit or stays on continuously.
There is a hardware connection problem.
•
Make sure that the cables are securely plugged in at the switch and the device.
•
Make sure that the connected device is turned on.
•
If the Ethernet cable is connected to a NIC or other Ethernet adapter, make sure
that the card or adapter is installed correctly and is working.
•
Make sure that the cable is less than 328 feet (100 meters).
Technical Support
Thank you for selecting NETGEAR products.
After installing your device, locate the serial number on the label of your product,
and use it to register your product at
http://www.NETGEAR.com/register
.
Registration is required to use the telephone support service. For product updates,
additional documentation, and support, go to
http://support.netgear.com
.
For complete DoC, go to the NETGEAR EU Declarations of Conformity website at
http://support.netgear.com/app/answers/detail/a_id/11621/
.
FS116P IG 30July2012.fm Page 2 Friday, August 3, 2012 11:18 AM
