NetComm NB6 User Manual Download Page 49

Page: 49 / 152

YML854 Rev1

NB6, NB6W, NB6Plus4W

User Guide

www.netcomm.com.au

PPP over ATM/ PPP over ethernet

If the connection type you choose is PPP over ATM or PPP over Ethernet, please refer to the following information.

According to the ISP’s configuration on the server, you can choose PPPoE or PPPoA modes.

Choose

PPPoA

PPPoE

and click

On this screen, you have to make the settings for WAN IP. To get the IP address automatically, click the

Obtain

an IP address automatically

radio button. Or click

Use the following IP address

button and enter the IP

address for WAN interface.

Check

Enable NAT

if you need.

MTU:

It means the maximum size of the packet that transmitted in the network. The packet of the data
greater than the value set here will be divided into several packets for transmitting.
Type the value into the field of

MTU

. The default MTU value for PPPoE is 1492; while for PPPoA is 1500.

Click

for the next procedure.

Summary of Contents for NB6

























































































































































Search results

Summary of Contents for NB6

Reviews:

Related manuals for NB6

Brands by name

Popular brands

NetComm NB6, User Manual

Search results

Summary of Contents for NB6

Reviews:

Related manuals for NB6

Brands by name

Popular brands