background image

210-0000025 rev04

!

192.168.254.252 if the MUM is in slot 13 (IPD12000) or slot 5 (IPD4000) 

!

192.168.254.253 if the MUM is in slot 14 (IPD12000) 

e. Log in with a default username and password (both of which are case sensitive). 

Please note that General Users have "read only" access; for NMS configuration you 
must log in as a Superuser. 

!

general / Password 

!

superuser / Password 

Accessing TAM1500-12 data in a previously installed IP DSLAM

a. Establish a connection with the MUM either directly (through the Ethernet RJ45 

MGMT port on the MUM faceplate) or, if the system has been so configured, from a 
PC on your network. 

b. For direct connections verify that the MGMT LNK LED on the MUM faceplate is 

illuminated indicating the connection has been established. 

c. Launch a web browser such as Microsoft Internet Explorer (v4.0 or higher) or 

Netscape Navigator (v4.0 or higher). 

d. Enter the assigned IP address* into the address field at the top of your browser 

window. Press the Enter key. 

e. Log in with your assigned username and password.* Please note that General Users 

have "read only" access; for NMS configuration you must log in as a Superuser. 

*If the IP address, username or password is unknown, contact your System Administrator 
or Information Technology Manager.

Default Settings

No configuration is necessary for the TAM1500-12 to operate at default settings. If however, a 
change is required, default settings can easily be modified within NMS. For information 
regarding specific parameter configurations, refer to the TAM1500-12 Circuit Configuration 
section on the following page and/or the Management User Guide for IP and Mini DSLAMs.

Management Password Administration Defaults*

NOTE

Once accessed initially, the management system within the MUM can be configured such that NMS 
and SNMP can be reached from any computer on your network. For further instruction please refer 
to the Management User Guide for IP and Mini DSLAMs.

General Username: general
General Password: Password

Super Username: superuser
Super Password: Password

*Usernames and passwords are case sensitive.

Summary of Contents for 12-Port T1 Access Multiplexer TAM1500-12









Reviews: