background image

Net Safety Monitoring 

 

MAN-0015 Rev 14 UVIRS-A/AR 

26 

November 07, 2008 
 

 

 

 

A

PPENDIX 

E:

 

UVIRS

 

DATA 

False Alarm Immunity 

Falsee Alarm Source 

Distance 

(ft/m) 

Modulated Unmodulated 

Sunlight direct 

-------- 

No Alarm 

No Alarm 

Sunlight indirect 

-------- 

No Alarm 

No Alarm 

Arc Welder 

30/9.1 

No Alarm 

-------- 

1500 Watt heater 

10/3.0 

No Alarm 

No Alarm 

40 Watt  Fluorescent Lights  

10/3.0 

No Alarm 

No Alarm 

500 Watt Halogen Light 

3/0.9 

No Alarm 

No Alarm 

250 Watt Incandescent Light 

3/0.9 

No Alarm 

No Alarm 

250 Watt Sodium Vapor Lamp 

10/3.0 

No Alarm 

No Alarm 

70 Watt Sodium Vapor Lamp 

10/3.0 

No Alarm 

No Alarm 

250 Watt Metal Halide Lamp 

10/3.0 

No Alarm 

No Alarm 

 

Response Testing w/ Un-modulated False Alarm Stimuli Present  

False Alarm Source 

False Alarm Source Distance (ft/m) 

Fire Source Fire 

Source 

Distance 

(ft/m) 

Sunlight direct 

--------------- 

16" Propane Plume 

25/7.62 

Sunlight indirect 

--------------- 

16" Propane Plume 

25/7.62 

1500 Watt heater 

10/3.0 

16" Propane Plume 

25/7.62 

40 Watt  Fluorescent Lights  

10/3.0 

16" Propane Plume 

25/7.62 

500 Watt Halogen Light 

3/0.9 

16" Propane Plume 

25/7.62 

250 Watt Incandescent Light 

3/0.9 

16" Propane Plume 

25/7.62 

250 Watt Sodium Vapor Lamp 

10/3.0 

16" Propane Plume 

25/7.62 

70 Watt Sodium Vapor Lamp 

10/3.0 

16" Propane Plume 

25/7.62 

250 Watt Metal Halide Lamp 

10/3.0 

16" Propane Plume 

25/7.62 

Summary of Contents for UV/IRS-A






























Reviews: