background image

MAN-0093 Rev 0 Oxygen Sensor 
June 2008 
Net Safety Monitoring Inc. 

 

 

 

 

IMPORTANT INFORMATION 

 

This manual is for informational purposes only. Although every effort has been made to ensure the correctness 
of the information, technical inaccuracies may occur and periodic changes may be made without notice. Net 
Safety Monitoring Inc., assumes no responsibility for any error contained within this manual. 

 

If the products or procedures are used for purposes other than as described in the manual, without receiving 
prior confirmation of validity or suitability, Net Safety Monitoring Inc. does not guarantee the results and 
assumes no obligation or liability. No part of this manual may be copied, disseminated or distributed without the 
express consent of Net Safety Monitoring Inc. 

 

Net Safety Monitoring Inc. products are carefully designed and manufactured from high quality components and 
can be expressed to provide many years of trouble free service. Each product is thoroughly tested, inspected and 
calibrated prior to shipment. Failures can occur which are beyond the control of the manufacturer. Failures can 
be minimized by adhering to the operating and maintenance instructions herein. Where the absolute greatest of 
reliability is required, redundancy should be designed into the system.  

 

WARRANTY 

 
Net Safety Monitoring Inc warrants this sensor against defective parts and workmanship for a period of 6 
months from date of purchase. No other warranties or liability, expressed or implied, will be honoured by Net 
Safety Monitoring Inc. Contact Net Safety Monitoring Inc. or an authorized representative for details. 
 
We welcome your input at Net Safety Monitoring Inc. If you have any comments please contact us at the 
telephone number or address below or visit our web-site, www.net-safety.com, and complete our on-line 
customer survey. 

 

If further language translation for this manual is required please contact:  
 

CONTACT INFORMATION 

 

Net Safety Monitoring Incorporated  

 

 

Direct:   (403) 219-0688 

Corporate Headquarters  

 

 

 

Facsimile:   (403) 219-0694 

2721 Hopewell Place NE  

 

 

 

E-mail: 

[email protected]

 

Calgary, AB Canada T1Y 7J7    

 

 

Web-site: www.net-safety.com 

 
 

 
 
 
 

Summary of Contents for ST340X-25-ASSY
























Reviews: