Guarantee service life is 24 months from the date of sale.
At the end of the service life the device is subject to disposal. The device does not pose a hazard to
human health and environment. The device does not contain any non-ferrous and precious metals.
Waste batteries should be disposed separately from mini remote controls.
Warranty obligations cease in case of non-observance of operating conditions established by the
manufacturer and mechanical damage during operation. Warranty obligations do not cover the case of
failure to present the device passport.
9. Disposal
Products must be transported in package in containers, closed railway cars, heated sealed
compartments of aircraft and holds, as well as automobile transport with protection against
precipitation at any distance at temperatures from -50°С to + 50°С, and with relative humidity up to
100% - at 25°С.When transporting products, protection from dust and atmospherical condensation
should be provided.
The average product life is at least 5 years.
8. Storage, transportation, service life
7. Current maintenance
10. Manufacturer's warranty
Guaranteed storage life is 6 months from the manufacturing date (the last 6 figures in the product
serial number, for example: 191120 – November 19, 2020).
If during operation the device fault is detected it is necessary to call maintenance personnel. Within
the warranty period servicing and repair are provided by the manufacturer dealer.
Products should be stored in packaging at temperatures from + 5°С to + 40°С and relative air humidity
of no more than 80% in heated and naturally ventilated warehouses, in air-conditioned warehouses in
the absence of aggressive impurities, conductive dust, acid fumes and alkalis, as well as gases that
cause corrosion and destroy insulation. During storage, sharp fluctuations in temperature (more than
3°C/min) and air humidity (more than 5%/min) are not allowed.
With the note of sale absent – from the manufacturing date.
13. Potential problems
D
PM
is not available for static and feedback mode!
5. Distance Programming Mode (DPM)
Action
Indication
DPM. The remote control should be programmed previously in the executive device
1. Enter the
DPM
with the pre-programmed remote control: press the «
STOP
» button of the
recorded channel and, while holding it, press the «UP» button. Hold both buttons for more than 4
seconds, then release them and briefly press the up button twice for 5 seconds.
2. After entering the DRP, you can perform the following actions:
a)
record
the channels of new remotes to the device memory;
c
) erase all device memory: press the «STOP» and «DOWN» buttons of the recorded remote
channel simultaneously, hold them for more than 4 seconds;
d) output the device from the DRP: press and hold the «STOP» button of the recorded channel of
the remote control, then briefly press the «UP» button.
b) delete channels of recorded remotes from device memory;
1. Roller shutter curtain will make a short-term movement
«
DOWN-UP
»
once, and after 5 sec. by
repeated short-term movement
«
DOWN-UP
»
it will confirm the input in the DPM.
b)
Roller shutter curtain will make long-term movement
«
DOWN-UP
»
.
a)
Roller shutter curtain will make long-term movement
«
DOWN
»
, short-term movement
«
UP-DOWN
»
,
and long-term movement
«
UP
»
.
d)
Roller shutter curtain will make short-term movement
«
DOWN-UP
»
twice.
c)
Roller shutter curtain will make long-term movement
«
DOWN-UP
»
twice.
2. Indication on the executive device:
6. Updating the remote control
The 8101-5 remote control can receive new updates if you have an online 8767 device. You must log in on your 8767 device. The update is only available in
the
feedback mode.
Action
Indication
The battery of the remote control must be charged, otherwise the update will not be installed (error alarm).
1.
S
imultaneously press and hold the «
UP»
and
«DOWN»
buttons until the second channel led lights
up and the second beep sounds, then release both buttons.
2.
I
n the app, add the remote control and activate the update download.
1. The indicators of all channels, from the 1st to the 5th, start flashing in waves.
2. The indicators continue to flash until the update is installed, and then turn off.
The remote control is updated within 10 minutes, forced interruption is available by the "stop" button.
Fig
. 2 —
R
eplacing batteries
11. Completeness
Remote Control Radio 8101-5 (see serial number on the first page) is manufactured in conformance
with RB TR
808001034.012-2018
, is approved by QCD and is classified as fit for operation.
12. Acceptance certificate
Remote Control
Radio 81
01-5 ..................................................................................................
.
....
.
.
.
.....1
pc
.
Passport
....................................................................................................................................
.
.....
.
.......1
pc
.
Individual packing
.............................................................................................................
..................
....1
pc
.
Made in Belarus
2
Version
1
SketchNero Group LLC
t
echnical support:
15, Bolshaya Ochakovskaya St.,
119361, Moscow.
8 800 5000-930
Representative offices
in Russian Federation:
Tel
.: +7 495 430-79-60
+7 495 735-64-47
Nero Electronics LLC
Tel
.: +375 17 388-53-00
Manufacturer and representative
office in Belarus
www.neroelectronics.by
+375 29 610-12-53
+375 29 609-25-59
Minsk FEZ, 223016, Minsk district,
Novy Dvor Rural Council, 74
t
echnical support:
+380 67 679-51-22
t
echnical support:
21, B. Khvoyki St., Office ,
03022, Kiev.
Representative office
in Ukraine:
Umnye resheniya LLC
Tel
.: +38 067 679-51-22
+38 044 500-18-55
Tel
.: +7 812 987-51-56
+7 981 757-90-45
t
echnical support:
Nero SPb LLC
195009, St. Petersburg
14, Komsomola St., Build. 2,
spb
-
8 800 5000-930
Problem
Probable reason
Fault elimination
The remote control is not recorded in the executive
devices.
1. Battery has run down (LED is off or blinks when you press the remote
control).
2.
The remote control in dynamic mode is not recorded
in the executive
devices which support only static transmissions.
1. Change battery.
2. Change the operation mode from dynamic to static one.
