Neousys Technology Nuvo-3000 Series User Manual Download Page 31

Page: 31 / 101

Nuvo-3000 Series User’s Manual

Page 31 of

101

2.3.3 COM Ports (COM1 & COM2)

Nuvo-3000 provides two COM ports on the back panel for communicating with external

devices. COM1 and COM2 are located on the back panel via 9-pin D-Sub male connectors.

They are implemented using industrial-grade ITE8783 Super IO chip (-40 to 85°C) and

provide up to 115200 bps baud rate.

Both COM1 and COM2 support software-selectable RS-232/422/485 mode. The operation

mode of COM1/COM2 can be set in BIOS setup utility (refer to section 4.1.1 for detail). The

following table describes the pin definition of COM ports.

For Nuvo-3000TB series, one additional RS-232 port (COM3) is provided via an internal

box header. For users who need the 3

COM port, Neousys offers a cable kit to connect the

internal connector and expose a 9-pin D-Sub connector on the back panel.

Pin#

RS-232 Mode

RS-422 Mode

RS-485 Mode

(Two-wire 485)

DCD

422 TXD+

485 TXD+/RXD+

422 RXD+

DTR

422 RXD-

GND

DSR

RTS

CTS

422 TXD-

485 TXD-/RXD-

Summary of Contents for Nuvo-3000 Series






























































































Search results

Summary of Contents for Nuvo-3000 Series

Reviews:

Related manuals for Nuvo-3000 Series

Brands by name

Popular brands

Neousys Technology Nuvo-3000 Series, User Manual

Search results

Summary of Contents for Nuvo-3000 Series

Reviews:

Related manuals for Nuvo-3000 Series

Brands by name

Popular brands