background image

- 3 - 

 

 

GENERAL WARNINGS 

 

READ and UNDERSTAND this manual completely before using 175lb Spike Aerator Spreader. 

Operator  must  read  and  understand  all  safety  and  warning  information,  operating  instructions, 
maintenance and storage instructions before operating this equipment. Failure to properly operate and 
maintain the aerator spreader could result in serious injury to the operator or bystanders. 
 

Operation Warnings 

  Do not at any time carry passengers, sit or stand on the aerator spreader.   

  Do not allow children to play on, stand upon or climb on the aerator spreader. 

  Always inspect the equipment before using to assure it is in good working condition. 

  Replace or repair damaged or worn parts immediately. 

  Always check and tighten hardware and assembled parts before operation. 

  Do not exceed equipment maximum hopper capacity of 175lb. 

  Avoid large holes and ditches when operating the equipment. 

  Be careful when operating the aerator spreader on steep grades (hill). 

  Always operate at reduce speed in rough terrain, along creeks, ditches and on hillsides. 

  Do not operate close to creeks, ditches and public highways. 

  To avoid personal injury and/or equipment damage 

DO NOT EXCEED 5MPH

  Always use caution when loading and unloading the hopper. 

  Only tow with recommended vehicles (Lawn/Garden Tractors and ATVs). 

 

Always refer to the vehicle owner’s manual for proper towing. 

  This equipment is not designed to be used with zero-turn mowers. 

  Always secure and lock aerator spreader to the vehicle hitch before operating. 

Crush and Cut Hazards 

  Always keep hands and feet clear from moving parts while operating the equipment. 

  Always clear and keep work area clean when operating.   

  Always

 

wear safety gear, eye protection, gloves and work boots when operating the aerator 

spreader.

 

.   

 

WARNING 

The  warnings,  cautions,  and  instructions  outlined  in  this  instruction  manual  cannot  cover  all 
possible  conditions  or  situations  that  may  occur.    It  must  be  understood  by  the  operator  that 
common  sense  and  caution  are  factors  which  cannot  be  built  into  this  product  and  must  be 
supplied by the operator.

 

 
 

 
 

Assembly Is Required

 

This product requires assembly before use. See 

“Assembly” section for instructions.    Because of the 

weight and/or size of the equipment, it is recommended that another adult be present to assist with the 
assembly.   

INSPECT ALL COMPONENTS

 closely upon receipt to make sure no components are 

missing or damaged. 
 

 
 
 
 
 
 
 
 
 
 

Summary of Contents for CT2214

















Reviews: