background image

Trouble shooting    

en

35

3

Trouble shooting

Trouble shooting

Usually, faults are small matters that are easy to 

eliminate. Please read the information in the table 

before calling the after-sales service.

Cleaning

How do I clean the hob?

Using a special glass-ceramic cleaning agent produces the best results. We advise against using harsh or abrasive cleaning agents, dish-

water detergent (concentrated) or scouring pads.
You can find more information on cleaning and caring for your hob in the section on 

~

 "Cleaning"

Indicator/symbol

Possible cause

Solution

None

The power supply has been disconnected. 

Use other electrical appliances to check whether a short circuit 

has occurred in the power supply. 

The appliance has not been connected as shown 

in the circuit diagram.

Make sure that the appliance has been connected as shown in 

the circuit diagram.

Electronics fault.

If the fault cannot be rectified, inform the technical after-sales ser-

vice.

The indicators are flashing

The control panel is damp or there is something 

on it.

Dry the control panel or remove the object.

Ù

 is flashing on the cooking 

zone displays

A fault has occurred in the electronics.

To acknowledge the fault, briefly cover the control panel with 

your hand.

”ƒ

 / 

“ˆ‹‚†

The electronics have overheated and have 

switched off the affected cooking zone.

Wait until the electronics have cooled down sufficiently. Then 

touch any symbol on the hob.

”…

 / 

“ˆ‹‚†

The electronics have overheated and all the 

cooking zones have been switched off.

Ӡ

 + heat setting and signal 

tone

There is hot cookware near the control panel. 

There is a risk that the electronics will overheat.

Remove the cookware that is causing the problem.The fault code 

will go out shortly afterwards. You can now resume cooking.

Ӡ

 and signal tone

There is hot cookware near the control panel. To 

protect the electronics, the cooking zone has 

been switched off.

Remove the cookware that is causing the problem. Wait a few 

seconds. Touch any touch control. When the fault code on the dis-

play goes out, you can resume cooking.

”‚

 / 

”‡

The cooking zone has overheated and has been 

switched off to protect the work surface.

Wait until the electronics have cooled down sufficiently before 

switching the cooking zone back on.

”‹

The transfer settings function will not activate

Acknowledge the fault code by touching any of the buttons. You 

can cook as usual without using the transfer settings function. 

Contact the technical after-sales service.

”Š

The FlexPlus cooking zone will not activate

Acknowledge the fault code by touching any of the buttons. You 

can use the other cooking zones to cook as usual. Contact the 

technical after-sales service.

”‰

The cooking zone has been operating continu-

ously for an extended period.

The automatic safety shut-off function has been activated. See 

the section entitled 

“ˆ‹‚‹

The hob is unable to connect to your home net-

work or the extractor hood.

Acknowledge the fault code by touching any of the buttons. You 

can cook as usual without a connection.
If this code is displayed again, contact the technical after-sales 

service.

“Š‹‹‹
“Š‹‚‹

The operating voltage is incorrect/outside of the 

normal operating range.

Contact your electricity supplier.

Do not place hot cookware on the control panel.

Summary of Contents for T68PT6QX0









































Reviews: