background image

Operating the appliance       

en

7

1

Operating the appliance

Operating the appliance

These instructions apply to several appliance variants. 

It is possible that individual features are described 

which do not apply to your appliance.

Note: 

Switch on the extractor hood when you start 

cooking and switch it off again several minutes after you 

have finished cooking. This is the most effective way of 

removing the kitchen fumes.

Control panel model 1

Setting the fan

Switching on

Touch the 

#

 symbol.

The fan starts at fan setting 2.

Selecting the fan setting

Touch the 

@

 or 

A

 symbol to set a different fan setting.

Switching off

Touch the 

#

 symbol.

Noise reduction function

The noise reduction function reduces the fan noise.

Switching on

Note: 

This function can be used at any fan setting 

except fan setting 

. The function will remain active 

even after the fan is switched off.

Touch the 

Q

 symbol.

Switching off

Touch the 

Q

 symbol.

AirFresh function

Switching on

Touch the 

3

 symbol.

3

 will be shown on the display panel.The fan runs for 

approximately 5 minutes per hour at fan setting 1.

Switching off

Touch the 

3

 symbol.

This ends the AirFresh function.

Intensive setting

You can use the intensive setting if there is a large 

build-up of odours and fumes/vapours.

Switching on

Touch the 

˜

 symbol. 

˜ƒ

 will light up on the display. 

Touch the 

˜

 symbol again to switch back to intensive 

mode 

˜‚

.

Note: 

After approx. 6 minutes, the extractor hood 

automatically switches back to fan setting 3.

Switching off

If you want to end intensive mode before the preset 

time expires, touch the 

˜

 symbol.

Symbol

Explanation

#

Fan on/off

Q

Noise reduction function

3

AirFresh function

A

Decrease fan setting

@

Increase fan settings/intensive mode 1, 2

˜

Intensive mode 2 shortcut

Automatic mode

6

Light on/off/dimming

Display

Explanation

Q

Noise reduction function

1-3

Fan settings

9

Fan run-on

3

AirFresh function

D

Hob-based hood control

Summary of Contents for EXTRACTOR HOOD

























Reviews: