background image

6

Operating procedure

The most effective method of removing kitchen fumes is to:

switch on the extractor hood 

when you start cooking.

switch off the extractor hood 

a few minutes after you finishing cooking.

The fans in this appliance can be switched to the desired setting by hand (manual mode)
or can be controlled fully automatically with the automatic function according to your 
requirements (automatic mode). 

Fan 
on / off

Switching on manual mode:

Press the 

L

or 

+

button.

The fan starts at Setting 

}

.

Switching on the fan settings/intensive
setting:

1.

To increase the fan settings or switch on
the intensive setting 

ç

, press the 

+

button.

The intensive setting operates at
maximum power which should be
used only briefly.
If the intensive setting is not switched
off manually, the fan automatically
switches back to Setting 

}

after 

10 minutes.

2.

To switch off the intensive setting 

ç

or

switch back to fan settings 

~

}

|

and

switch off the extractor hood 
completely, press the 

button.

Switching over to automatic mode:

To switch from manual mode to 
automatic mode at any time, press the 

Ü

button.

Fan – off –
Fan settings – lower –

Fan – on –
Fan settings – higher –

Fan run-on /
Intermittent ventilation

Light 
on / off

Display:

Fan settings / Intensive setting

Saturation – grease filter 

(

#

)

Saturation – activated carbon filter 

(

ã

)

Automatic mode / Manual mode

Summary of Contents for D99T6N0GB

























Reviews: