background image

6

Operating the appliance

These instructions apply to several appliance variants. It is 

possible that individual features are described which do not 

apply to your appliance.

Note: 

Switch on the extractor hood when you start cooking and 

switch it off again several minutes after you have finished 

cooking. This is the most effective way of removing the kitchen 

fumes.

Control panel

Setting the fan

Switching on

Press the 

#

, 2

9

, 3

8

 or 

˜

 button.

Switching off

Press the 

#

 button.

Note: 

If fan level 2 or 3 is switched on, press the 

#

 button 

twice.

Intensive setting

You can use the intensive setting if there is a large build-up of 

odours and fumes/vapours.
Press the 

˜

 button.

Intensive mode is activated.

Notes

The intensive mode run time is limited to 6 minutes.

Once 6 minutes has elapsed, the appliance switches back to 

the fan level that was previously selected.

Intensive mode can be activated when the appliance is 

switched off; once 6 minutes has elapsed, the appliance 

switches itself off again.

Fan run-on

With the fan run-on, the appliance continues to run at the level 

that was previously set and switches off automatically after 

30 minutes.

1.

Set the fan level.

2.

Press and hold the 2

9

 button.

Fan run-on mode is activated. The button for this level flashes 

green.

Interval ventilation

With interval ventilation, the ventilation system switches on 

automatically at the lowest level for 10 minutes every hour. The 

interval ventilation switches off after 24 hours.

Switching on

Press and hold the 3

8

 button.

The interval ventilation is activated. The 

#

 button flashes.

Switching off

Press and hold the 3

8

 button or press the 

#

 button.

Lighting

The lighting can be switched on and off independently of the 

ventilation system.
Press the 

6

 button.

The lighting is switched on.

Setting the brightness

Press and hold the 

6

 button until the desired brightness is 

reached.

Saturation indicator

If F is lit, this means that the integrated filters are saturated:
Lit permanently: clean the metal grease filter
For instructions on how to clean metal grease filters, refer to the 

section 

Cleaning and maintenance

.

Resetting the saturation indicator

1.

Switch off the appliance.

2.

Press and hold the 

#

 button for 3 seconds.

The saturation indicator is reset. F goes out.

Explanation

6

Light on/off

#

Fan off/fan level 1

2

9

Fan level 2/fan run-on

3

8

Fan level 3/interval ventilation

˜

Intensive mode

F

Saturation indicator

)

Summary of Contents for D57ML6.N1













Reviews: