en
Basic operation
12
5.
Use the button to navigate to the next row.
6.
Use the or button to select the correct year.
7.
Press the button repeatedly until "Date" appears.
8.
Use the button to apply the settings.
Setting the water hardness
1.
Use the button to navigate to the bottom row.
2.
Use the or button to select the water hardness
range.
→
"Before using for the first time", Page 11
3.
Use the button to navigate back to the top row.
4.
Use the button to save your settings.
5.
Open and close the appliance door once.
a
The appliance will perform a self-test, after which it
will be ready to use.
a
Initial configuration is now complete.
6.3 Calibrating and cleaning the appliance
You will need to calibrate the appliance and clean the
cooking compartment and accessories before using it
to cook food for the first time.
Note:
The boiling point of water depends on the air
pressure. During the calibration process, the appliance
makes adjustments to adapt it to the pressure condi-
tions in the location where it is installed.
Requirement:
The cooking compartment must have
cooled down completely.
1.
Remove the product information, accessories and
any leftover packaging (e.g. polystyrene pellets)
from the cooking compartment.
2.
Wipe the smooth surfaces in the cooking compart-
ment with a soft, damp cloth.
3.
Press to switch the appliance on.
→
"Switching on the appliance", Page 12
4.
Fill the water tank.
→
"Filling the water tank", Page 13
5.
Set the required type of heating, temperature and
cooking time for the calibration process and press
to start.
Calibration
Type of heating
Steam
Temperature
100 °C
Duration
30 minutes
Tip:
Do not open the appliance door while calibra-
tion is in progress. Calibration will otherwise be in-
terrupted.
a
Calibration starts. This generates a lot of steam.
6. ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures
above 120 °C, this will damage the enamel.
▶
Do not use the appliance if there is water on the
cooking compartment floor.
▶
Wipe away any water on the cooking compart-
ment floor before operation.
Allow the appliance to cool down and then wipe
away the water from the cooking compartment floor.
7.
Set the required type of heating and temperature for
the heat-up process and press to start.
→
"Setting the type of heating and temperature",
Heating up
Type of heating
CircoTherm hot air
Temperature
Maximum
Duration
30 minutes
8.
Ventilate the kitchen while the appliance is heating.
9.
Press to switch off the appliance after
30 minutes.
→
"Switching off the appliance", Page 12
10.
Allow the appliance to cool down.
11.
Clean the smooth surfaces with soapy water and a
dish cloth.
12.
Empty the water tank and dry the cooking compart-
ment.
→
"After every steam operation", Page 16
13.
Thoroughly clean any accessories you used with
soapy water and a dish cloth.
Note:
The appliance retains the calibration settings,
even in the event of a power cut or disconnection from
the mains.
Tip:
To ensure that the calibration settings are updated
to accommodate the conditions at the new location
when you move house, restore the appliance's factory
settings in the basic settings. Then repeat the calibra-
tion procedure.
→
7 Basic operation
7.1 Switching on the appliance
▶
Press to switch the appliance on.
Notes
¡
In the basic settings, you can specify whether the
heating functions or the main menu should appear
when you switch on the appliance.
→
¡
If you do not perform any actions on the appliance
for an extended period, it will automatically switch it-
self off.
7.2 Switching off the appliance
▶
Press to switch the appliance off.
Notes
¡
The residual heat indicator will appear on the dis-
play while the cooking compartment is still hot.
→
"Residual heat indicator", Page 13
¡
The cooling fan will continue to run until the cooking
compartment has cooled down.
→
