background image

 

Doc. no: 312-0003-002-001 Rev 1.06 

 

Page 6 of 19

 

 

 

Firmware upgrade of units: 

This section describes how to firmware upgrade the units. On 312-0003 you can upgrade the unit by using the 
homepage (go to [maintenance] page and use the upgrade firmware). On all units you can use the procedure as 
bellow. 
First you need to go to 

www.neets.dk

 and find the newest version (or the version you want). The filename of 

the firmware are “aud_0100.bin” for version 1.00 (version 2.03 will be named “aud_0203.bin”.

 

Then you need to have a Micro SD to USB converter, you can get those from the internet (search google for 

“buy micro SD to USB converter” they cost from 10EUR) or by contacting Neets or you local distributor.

 

 

x

 

When you have the correct firmware and a converter to copy the file 
to the Micro SD card from your computer you are ready to firmware 
upgrade you unit. 

 

x

 

First you 

MUST

 disconnect the power from the audio amplifier. 

 

x

 

Then remove the SD Card from the unit by pushing the SD Card 

gently

 

into the unit about 1mm (either by using your finger tips or a flat 
screwdriver) and then let go and it will slide out. 

 

x

 

Place the Micro SD card into the adapter (e.g. USB adapter).  

 

x

 

Connect the adapter to your computer. 

 

x

 

Browse to the root of the folder of you SD card (e.g. : L:\) and copy 
the file you have downloaded to the root folder (in this case 

“aud_0100.bin”). Please make sure that you do not delete anything 

else from the card. 

 

x

 

 

 

x

 

Use safe way of removing the Micro SD card from your computer. 

 

x

 

Insert the Micro SD card to the unit (while power still is off)  

 

x

 

Connect power

 

x

 

Wait for LED to indicate “firmware done”

 (see the picture here to the 

right for LED indication). Input 1 will light up, while Standby and mute 

will make “light show”

 

 

x

 

Disconnect power and reconnect power. YOU ARE DONE…!

 

 

 

 

 
How to remove the SD-Card 

 

REMEMBER to remove 

power from unit before 

removing Micro SD 

card! 

 

 
SD Card insert to computer 

Firmware upgrade done..! 

Summary of Contents for 312-0001





















Reviews: