manualshive.com logo in svg

Neets Control LiMa, Installation Manual

Share
Download
Neets Control LiMa Installation Manual Download Page 2

Page 2 of 12

Foreword

This document describes how to install and operate the Neets Control - LiMa. 

COPYRIGHT - All information contained in this manual is the intellectual property and copyrighted

material of Neets. All rights are reserved. You may not allow any third party access to content,

information or data in this manual without Neets’ express written consent.

CHANGES - Neets reserve the right to change the specification and functions of this product

without prior notice.

Questions, AFTER reading this manual, can be addressed to your local distributor or:

Neets A/S

Langballe 4

8700 Horsens

Denmark

by E-Mail: [email protected]

or you may use our contact form at www.neets.dk

Revision list

This document has the following revision changes: 

Author: Date

Description

Pages

Rev

TBB: 09-08-2018 First release.

All

1.00

What is in the box?

When you open the box it will contain the following items: 

• 1 x Neets Control - LiMa
• 5  x Terminal connectors
• 2 x Screws and plugs for wall mounting O4 x 60 mm
• 2 x Screws for mounting on Neets Rack Shelf M4 x 35 mm
• Manual

!

Note that PoE power injector is not included. Use the PoE Injector 
(Part num ber: 302-000508). 

Summary of Contents for LiMa













Reviews:

No comments

Brands by name

Popular brands

Load more brands