Nederman FilterCart Advanced+, Instruction And Operation Manual, Page: 14 / 16

FilterCart A
EN
1 Disconnect the
power
cable.
2 Unlock the locks and remove the filter casing.
3 Use the plastic bag
supplied
with the new fil
ter
cartridge and pull it over the used cartridge.
Fold the plastic bag under the cartridge.
4 Use a duster to wipe off the filter cartridge con-
tact surfaces in the FilterCart A. Put the
duster in the plastic bag with the filter cartridge
and close the bag with the band supplied.
5 Handle the used filter cartridge according to the
relevant regulations for the substances that have
been collected.
6 Check that the pressure drop hose (from the con-
trol board) not is damaged and is fitted properly.
7 Check that the new filter cartridge is not damaged.
Also, check that the seal fitted on the underside
of the cartridge is not damaged. Then fit the cart-
ridge on the FilterCart A.
8 Refit the filter casing. Make sure the
locks tighten
to
the filter casing properly.
• A: Increasing the locking power.
• B: Decreasing the locking power.
6.2 Changing the HEPA-filter (access-
ory)
See Figure 8 . If the FilterCart A has been
supplied with a HEPA-filter, this is to be changed at
the same time as the main filter cartridge is changed.
WARNING! Risk of personal injury
Use necessary personal safety equipment
when changing the HEPA-filter.
Change the HEPA-filter cartridge in the following way:
1
Disconnect the
power
cable.
2 Unscrew the top cover.
3 Remove the used HEPA-filter and put it in the
plastic bag
supplied
with the new HEPA filter.
Close the plastic bag with the band supplied.
4 Handle the used HEPA-filter according to the rel-
evant regulations for the substances that have
been collected.
5 Check that the new HEPA-filter, item A, is not
damaged.
NOTE!
The filter surface must not be touched.
6 Verify that the UP-arrow, item B, is pointing up-
wards. Handle the HEPA-filter very carefully and
fit it in the FilterCart A. Ensure it is fitted
in the correct position and that the seal is down-
wards. Check that the seal not is damaged.
7 Refit the top cover. Fasten it securely.
7 Spare Parts
CAUTION! Risk of equipment damage
Use only N
$
e
$
d
$
e
$
r
$
m
$
a
$
n
$
original spare parts and ac-
cessories.
Contact your nearest authorized distributor or
N
$
e
$
d
$
e
$
r
$
m
$
a
$
n
$
for advice on technical service or
if you require help with spare parts. See also
w
$
w
$
w
$
.
$
n
$
e
$
d
$
e
$
r
$
m
$
a
$
n
$
.
$
c
$
o
$
m
$
.
7.1 Ordering spare parts
When ordering spare parts always state the following:
• The control number (see the
product identification
plate).
•
Part
number and name of the spare part (see
https://www.nederman.com/en-us/service/spare-
part-search
• Quantity of the parts required.
8 Accessories
•
•
HEPA-filter H13,
81 ft 2 (
7.5 m
2
)
high-efficiency
fi
nal
filter, class H13.
Spark protection, for mounting in the hood. To re-
duce the risk of fire.
9 Recycling
The product has been designed for component mater-
ials to be recycled. Different material types must be
handled according to relevant local regulations. Con-
tact the distributor or
$
N
$
e
$
d
$
e
$
r
$
m
$
a
$
n
$
if uncertainties arise
when scrapping the product at the end of its service
life.
1
4