E–16
This section describes how to set up your VT650 projector and
how to connect video and audio sources.
Setting up Your Projector
Your VT650 Projector is simple to set up and use. But before
you get started, you must first:
1. Determine the image size.
2. Set up a screen or select a non-glossy white wall onto which
you can project your image.
Carrying the Projector: Always carry your projector by
the handle. Ensure that the power cable and any other cables
connecting to video sources are disconnected before moving the
projector.
When moving the projector or when it is not in use, cover the
lens with the lens cap.
M
E
N
U
EN
T
E
R
C
A
N
CE
L
SELECT
POWER
STATUS
ON
/OFF
SOURCE
AUTO
ADJUST
Screen
Top view
Screen
Side view
M
E
N
U
E
N
T
E
R
CA
NC
EL
SELECT
POWER
STATUS
ON
/OFF
SOURCE
AUTO
ADJUST
RG
B
INP
UT
OU
TP
UT
AU
D
IN
IN
OU
T
OU
T
PC
-C
ON
TR
OL
S-VID
EO
VID
EO
M
EN
U
EN
TE
R
CA
NC
EL
SELECT
POWER
STATUS
ON
/OFF
SOURCE
AUTO
ADJUST
RG
B
INP
UT
OU
TPU
T
AU
D
IN
OU
T
PC
-C
ON
TR
OL
S-V
IDEO
VID
2
1
M
EN
U
EL
LE
CT
SOURCE
AUTO
AD
JUST
RG
B
INP
UT
OU
TPU
T
AU
D
IN
OU
T
PC
-CO
NTR
OL
S-V
IDE
O
VID
Adjusting the Tilt Foot
1) Press and hold the Tilt button on the front of the pro-
jector.
2) Lift the front edge of the projector to the height you
want, and release the button to lock the Adjustable
Tilt Foot.
To fine-tune the image’s position vertically on the screen,
rotate the foot. Each of the rear feet height can be
changed up to 0.6” (4mm).
Carrying handle
2. INSTALLATION
Selecting a Location
The further your projector is from the screen or wall, the larger
the image. The minimum size the image can be is approximately
25" (0.64 m) measured diagonally when the projector is roughly
3.5 feet (1.1 m) from the wall or screen. The largest the image
can be is 300" (7.6 m) when the projector is about 36.6 feet (11.2
m) from the wall or screen.
Using a Tabletop or Cart
1. Place your projector on a flat level surface at the optimal dis-
tance from the screen or wall so you realize the size image
you want. (Avoid having bright room lighting or sun light
directly on the screen or wall where you’ll be projecting the
image.)
2. Connect the power cable, remove the lens cap and turn the
projector on. (If no input signal is available, the projector
will display a background image.)
3. Ensure that the projector is square to the screen.
4. Move the projector left or right to center the image horizon-
tally on the screen.
5. To center the image vertically, lift the front edge of the pro-
jector and press the One-Touch Tilt button on the front side
of the projector to release the Front Adjustable foot.
(There is approximately 10 degrees of up and down adjust-
ment for the front of the projector.)
6. If the projected image does not appear square to the screen
then use keystone correction for proper adjustment.
7. Adjust the size of the image using the Zoom lever on the
lens.
ME
NU
E
NTER
CA
NC
EL
SE
LE
CT
PO
WE
R
ST
AT
US
ON
/O
FF
SO
UR
CE