NEC T30A User Manual Download Page 155

Page: 155 / 252

-128-

6.2

Basic Operation of encryption key management function

This chapter describes the most basic operations under the conditions below. If you want to perform

operations under other conditions, make sure that you fully understand the description in this chapter,
and then go to “Advanced Operations” .

[Conditions]

Item

Condition

Tape media in the Library

All are LTO6 / LTO7 medium.

Key to be used

Master key only (Encryption keys are not used.)

Sharing tape medium among multiple libraries

Enabled by setting the same master key.

6.2.1

Setup

To set up the encryption key management function, perform the following procedure:

To set up the function

Registering the activation key

(See 6.2.1.1)

Enabling the encryption key management function

(See 6.2.1.3)

Registering (importing) the master key

(See 6.2.1.4)

Done

Exporting (backing up) the master key

(See 6.2.1.5)

Summary of Contents for T30A





























































































































































































































































Search results

Summary of Contents for T30A

Reviews:

Related manuals for T30A

Brands by name

Popular brands

NEC T30A, User Manual

Search results

Summary of Contents for T30A

Reviews:

Related manuals for T30A

Brands by name

Popular brands