NEC T30A User Manual Download Page 114 | Manualshive

Page: 114 / 252

background image

-87-

1. Library Map

This shows the physical positions of cartridges stored in the Library, as well as images of the
Library's various components such as the Accessor and drive.

2. Details (Magazine)

(1)Slot Information

This section shows detailed information about the selected slot.
Slot type              : Indicates the type of slot.
                                  (Storage / I/O Station / Cleaning / Inactive)
Element address : Indicates the slot's address for reporting to the host.

(2)Cartridge Information

Detailed information on the cartridge is displayed when a slot with a cartridge is selected.
Cartridge label : Shows the cartridge's bar code label.
                            "Unknown" is displayed when there is no barcode label.
Remain            : Indicates the number of cleaning cartridges remaining.
              This is shown only when the cartridge type is "cleaning cartridge".
Media Status        : Indicates the cartridge's status. (OK, Expired, Bad Media, etc.)
Encryptions      : Indicates the encryption status.(Encrypted,Not encrypted,unknown)
Total Capacity :Indicates the total capacity of tape cartridge.
Used Capacity :Indicates the used capacity of tape cartridge.
Remaining Capacity :Indicates the remaining capacity of tape cartridge.

The correct remaining number cannot be shown unless a cleaning cartridge has
been loaded to the drive. Note that cartridge cleaning starts automatically when a
cleaning cartridge is loaded. Users are expected to monitor the number of times such
cleaning has been used.

Figure 5-6 Detail(Magazine)

«
...
112
113
114
115
116
...
»

Summary of Contents for T30A





























































































































































































































































Reviews:

No comments

Related manuals for T30A

Brand: Gardiun Pages: 27

Brand: IBM Pages: 230

Spinpiont HD320KJ

Brand: Samsung Pages: 1

Brand: Lifetime Pages: 32

Brand: SentrySafe Pages: 2

Brand: Facom Pages: 2

Brand: dallmeier Pages: 32

Brand: iStorage Pages: 23

Brand: Oracle Pages: 146

PREMIER GAMT41HWJG

Brand: Gladiator Pages: 24

Brand: morse Pages: 11

Brand: Bosch Pages: 30

Brand: Bosch Pages: 68

Brand: Canon Pages: 76

Brand: QNAP Pages: 39

Brand: IBM Pages: 208

FileStore N8300

Brand: Symantec Pages: 55

Brand: XtendLan Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands