NEC N8151-44F Instruction Manual Download Page 22 | Manualshive

Page: 22 / 48

background image

4

Built-in AIT

Setup

The procedure up to installation of the Built-In AIT to the “basic processing unit” is explained in
the following.

Setting the Built-In AIT

- Setting with the jumper pins -

You can change the following settings with the jumper pins on the rear of the Built-In AIT.

• SCSI ID (factory-set to “ID4”)
• Parity function (factory-set to “Enabled”)

Hint

✎

“With strap” means a status that the straps are attached to two pins. “Without strap” means a
status that no strap is attached to either pin or it is attached to one of two pins.

Hint

✎

“Without strap” means that one strap is
attached to one of the two pins, or that
the strap has been removed altogether.
If you remove the strap, make sure you
store it in a safe place.

SCSI ID (pin 0 to 3 from right)

Unused (NC)

Parity (PD)

«
...
20
21
22
23
24
...
»

Summary of Contents for N8151-44F

















































Reviews:

No comments

Related manuals for N8151-44F

StorNext QM1200

Brand: Quantum Pages: 9

HIMALAYA 100.S/2/CC

Brand: garofalo Pages: 12

Brand: U-Line Pages: 3

Brand: SanDisk Pages: 2

G-DRIVE mobile USB

Brand: G-Technology Pages: 32

Brand: LaCie Pages: 2

Brand: Patiowell Pages: 38

Brand: M-Systems Pages: 22

Save2Data SecureKey

Brand: Hama Pages: 38

Brand: Home Decorators Collection Pages: 4

Brand: OYEN DIGITAL Pages: 1

Brand: Asus Pages: 32

Brand: Asus Pages: 40

Brand: Asus Pages: 58

Brand: Asus Pages: 10

Brand: Asus Pages: 8

Leather External HDD USB 3.0

Brand: Asus Pages: 2

Brand: Asus Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands