background image

 

 

(7)

 

Slide two slide rails out from the rack until they were locked. And then with three or 
more persons assisting you, lift the server and align the inner rails attached to the 
both side of the server with the extended rails. 

(8)

 

Insert the inner rails into the extended slide rails and push the server into the rack 
until it stops. 

(9)

 

Carefully press down the release levers on the inner rails to release the locks and slide 
the server all the way into the rack. 

(10)

 

To check that the server slides in and out of the rack, grasp the two handles on the 
front of the server slowly pull the server out and push it back in. 

(11)

 

Tighten the four captive thumbscrews to secure the server to the rack. 

 

 

 

Note sufficiently that your fingers may not be caught between a 
rail and other  mechanical parts or cut by a rail at installation or 
removal of the server from the rack. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

   

 

 

 

?

 

Do not connect any cables before attaching the cable arm. 

?

 

Secure four captive thumbscrews when mounting the server to the rack. 

 

Captive thumbscrews

 

Front Cover 

 

Release Lever 

Summary of Contents for N8143-56E
















Reviews: