NEC N8102-686 User Manual Download Page 7

CBZ-001279-686-01 

 

 

3. 増設後の確認 

Operation Check after Installation 

 

(1) 本メモリボードを増設後、本体装置の画面が表示されない場合は、基本で実装されているメモリも 

含めて、再度すべてのメモリが正しく実装されているか確認してください。 

After  adding  this  memory  card,  if  nothing  is  displayed  on  the  main  unit  screen,  please  reconfirm 
that all memories including pre-installed ones are properly mounted. 

 

(2) POST の画面でエラーメッセージが表示されていないことを確認してください。 

Power on the server and verify that POST displays no error messages. 

 

(3) 本体装置の「SETUP」を立ち上げ、「Advanced」−「Memory Configuration」−「Memory Information」 

を選択し、増設したメモリの DIMM ステータス表示が「数値」になっていることを確認してください。 

Run  the  BIOS  SETUP  utility  and  select  [Advanced]  

  [Memory  Configuration]  

−「

Memory 

Information

to verify that the installed DIMM shows the status 

Number

 

(4) 増設したメモリが認識されない場合は、本体装置の「SETUP」を立ち上げ、「Advanced」―「Memory 

Configuration」−「Memory Retest」で「Yes」を選択して、メモリのエラー情報をクリアして 
ください。 
「SETUP」の立ち上げ、選択方法等は、本体装置の EXPRESSBUILDER に格納されているユーザーズガ
イドを参照してください。 

Select 

Yes

 for 

Memory Retest

」 

on the 

Advanced

」−「

Memory Configuration

menu. 

 

 

4. メモリ機能の利用 

Using the Memory RAS Features 

 

(1) 本製品には、メモリ RAS 機能として「標準機能(x4 SDDC)」を持っています。 

(N8102-686/687 は非対応) 
SDDC(Single Device Data Correction)はメモリ障害(複数ビット障害)を自動的に修正する機能です。 

The server has RAS feature including "Standard feature (x4 SDDC ECC memory)

. (N8102-

686F/687F is not supported) 
SDDC (Single Device Data Correction) allows automatic correction of memory error (multi-bit error). 

 

(2) 本体装置のマザーボードは、メモリを制御するための「メモリチャンネル」が 4 系統に分かれて 

います。 

The memory area on the motherboard of the server is divided into four memory channels as shown 
in the figure below. 

 
 

 
 
 
 
 
 
 
 

 
 
 
 
 
 

 

メモリコントローラ 

Memory Controller 

 

メモリコントローラ 

Memory Controller 

 

Summary of Contents for N8102-686









Reviews: